Analysis of fracture toughness and crack propagation of Ti6Al4V produced by selective laser melting

Advanced Engineering Materials

Volumn 14, Issue 1-2, 2012, Pages 92-97

  Van Hooreweder, Brecht ^a   Moens, David ^b   Boonen, Rene ^a   Kruth, Jean Pierre ^a   Sas, Paul ^a  

^a UNIVERSITY OF LEUVEN   (Belgium)

^b Lessius Mechelen   (Belgium)

Author keywords

[No Author keywords available]

Indexed keywords

BRITTLE BEHAVIOR; FAILURE MECHANISM; FINAL FAILURES; FINE-GRAINED MICROSTRUCTURE; FRACTURE MECHANISMS; FRACTURED SURFACES; IN-PHASE; MARTENSITE PHASE; MATERIAL DENSITY; MICROSTRUCTURAL ANALYSIS; POWDER PARTICLES; PROCESS PARAMETERS; RELATIVE DENSITY; SELECTIVE LASER MELTING; STATIC AND DYNAMIC BEHAVIORS; TI-6AL-4V; VACUUM ARCS;

GRAIN BOUNDARIES; MICROSTRUCTURE; TITANIUM; VACUUM APPLICATIONS;

CRACK PROPAGATION;

EID: 84856859388     PISSN: 14381656     EISSN: 15272648     Source Type: Journal    
DOI: 10.1002/adem.201100233     Document Type: Article

References (20)

1. J. P. Kruth, G. Levy, F. Klocke, T. H. C. Childs, Ann. CIRP 2007, 56, 730.
2. L. Lü, J. Fuh, Laser-Induced Materials and Processes for Rapid Prototyping, Kluwer, London 2001.
3. R. Noorani, Rapid Prototyping: Principles and Applications, Wiley, New Jersey, NJ 2005.
4. M. A. Lopez-Heredia, E. Goyenvalle, E. Aguado, P. Pilet, C. Leroux, M. Dorget, P. Weiss, P. Layrolle, J. Biomed. Mater. Res. Part A 2008, 85A, 664.
5. I. Yadroitsev, L. Thivillon, Ph. Bertrand, I. Smurov, Appl. Surf. Sci. 2007, 254, 980.
6. K. Osakada, M. Shiomi, Int. J. Mach. Tools Manuf. 2006, 46, 1188.
7. T. Gielis, M. Fleurinck, J. Bormans, B. Van Hooreweder, Development of a monoblock titanium steering wheel for a solar powered race vehicle using SLM. FISITA World Automotive Congress, 2010.
8. J. P. Kruth, M. Badrossamay, E. Yasa, J. Deckers, L. Thijs, J. Van Humbeeck, Part and material properties in selective laser melting of metals. 16th International Symposium on Electromachining, 2010.
9. E. Yasa, J. Deckers, J. P. Kruth, M. Rombouts, J. Luyten, Experimental Investigation of Charpy Impact Tests on Metallic SLM Parts. Int. Conf. Adv. Res. Virt. Rapid Prototyping, 2009, pp. 207-214.
10. L. Thijs, F. Verhaeghe, T. Craeghs, J. Van Humbeeck, J. P. Kruth, Acta Mater. 2010, 58, 3303.
11. G. Lütjering, Mater. Sci. Eng. 1998, A243, 32.
12. B. Van Hooreweder, F. De Coninck, D. Moens, R. Boonen, P. Sas, Polym. Test. 2010, 19, 319.
13. J. Van Vaerenbergh, Process Optimisation in Selective Laser Melting, Ph.D. Thesis, UTwente, 2008.
14. 1c of metallic materials, annual book of ASTM standards, Pennsylvania, US 1995.
15. ASTM E647, Standard test method for measurement of fatigue crack growth rates, annual book of ASTM standards, Pennsylvania, US 1995.
16. E. W. Collings, Materials Properties Handbook: Titanium Alloys, ASTM International, Materials Park, OH 1994.
17. M. J. Donachie, Titanium, a Technical Guide, ASTM International, Materials Park, Ohio, USA 1988.
18. R. K. Nalla, B. L. Boyce, J. P. Campbell, J. O. Peters, R. O. Ritchie, Metall. Mater. Trans. A 2002, 33A, 899.
19. G. R. Yoder, L. A. Cooley, T. W. Crooker, Eng. Fract. Mech. 1983, 17, 185.
20. G. Lütjering, J. Albrecht, A. Gysler, in Titanium: Science and Technology (Eds:, F. H. Froes, I. Caplan,), TMS, Warrendale, PA 1993, pp. 1635-1646.