High-frequency induction heated sintering of ball milled Fe-WC nanocomposites

International Journal of Minerals, Metallurgy and Materials

Volumn 20, Issue 7, 2013, Pages 693-699

  Zakeri, M ^a   Zanganeh, T ^b   Najafi, A ^b  

^a MATERIALS AND ENERGY RESEARCH CENTER   (Iran)

^b ISLAMIC AZAD UNIVERSITY   (Iran)

Author keywords

induction heating; iron; mechanical properties; metallic matrix composites; nanocomposites; sintering; tungsten carbide

Indexed keywords

ARCHIMEDES METHODS; BRINELL HARDNESS; HIGH-FREQUENCY INDUCTION HEATED SINTERING; MILLING SPEED; MILLING TIME; RELATIVE DENSITY; SINTERED SAMPLES; WC PARTICLES;

BRITTLE FRACTURE; COMPRESSION TESTING; INDUCTION HEATING; IRON; MECHANICAL PROPERTIES; METALLIC MATRIX COMPOSITES; MILLING (MACHINING); NANOCOMPOSITES; POWDERS; TUNGSTEN CARBIDE; X RAY DIFFRACTION; X RAY POWDER DIFFRACTION;

SINTERING;

EID: 84890264186     PISSN: 16744799     EISSN: 1869103X     Source Type: Journal    
DOI: 10.1007/s12613-013-0785-5     Document Type: Article

References (22)

1. K. Aldas and M.D. Mat, Experimental and theoretical analysis of particle distribution in particulate metal matrix composites, J. Mater. Process. Technol., 160(2005), No. 3, p. 289.
2. J. Hashim, L. Looney, and M.S.J. Hashmi, Particle distribution in cast metal matrix composites: Part I, J. Mater. Process. Technol., 123(2002), No. 2, p. 251.
3. I.J. Shon, B.R. Kim, J.M. Doh, and J.K. Yoon, Consolidation of binderless nanostructured titanium carbide by high-frequency induction heated sintering, Ceram. Int., 36(2010), No. 6, p. 1797.
4. H. Romanus, V. Cimalla, J. Schaefer, L. Spie G. Ecke, and J. Pezoldt, Preparation of single phase tungsten carbide by annealing of sputtered tungsten-carbon layers, Thin Solid Films, 359(2000), No. 2, p. 146.
5. L. Niu, M. Hojamberdiev, and Y.H. Xu, Preparation of in situ-formed WC/Fe composite on gray cast iron substrate by a centrifugal casting process, J. Mater. Process. Technol., 210(2010), No. 14, p. 1986.
6. p/duplex stainless steels matrix composites processing by laser melt injection, Surf. Coat. Technol., 202(2008), No. 10, p. 2113.
7. M.H. Korkut, O. Yilmaz, and S. Buytoz, Effect of aging on the microstructure and toughness of the interface zone of a gas tungsten arc (GTA) synthesized Fe-Cr-Si-Mo-C coated low carbon steel, Surf. Coat. Technol., 157(2002), No. 1, p. 5.
8. K. Miyazaki, S. Ito, N. Koura, N. Yoneda, and K. Asaka, Preparation of tungsten carbide-iron composite using HIP, J. Jpn. Soc. Powder Powder Metall., 37(1990), No. 2, p. 219.
9. Q.C. Jiang, X.L. Li, and H.Y. Wang, Fabrication of TiC particulate reinforced magnesium matrix composites, Scripta Mater., 48(2003), No. 6, p.713.
10. W.H. Jiang, J. Fei, and X.L. Han, Synthesis of titanium and tungsten carbides in iron matrices, J. Mater. Sci. Lett., 20(2001), No. 3, p. 283.
11. M. Razavi, M.R. Rahimipour, and R. Yazdani-Rad, Synthesis of Fe-WC nanocomposite from industrial ferrotungsten via mechanical alloying method, Adv. Appl. Ceram., 110(2011), No. 6, p. 367.
12. K. Chu, C.C. Jia, X.B. Liang, and H. Chen, Effect of sintering temperature on the microstructure and thermal conductivity of Al/diamond composites prepared by spark plasma sintering, Int. J. Miner. Metall. Mater., 17(2010), No. 2, p. 234.
13. K. Chu, Z.F. Liu, C.C. Jia, H. Chen, X.B. Liang, W.J. Gao, W.H. Tian, and H. Guo, Thermal conductivity of SPS consolidated Cu/diamond composites with Cr-coated diamond particles, J. Alloys Compd., 490(2010), No. 1-2, p. 453.
14. 2-SiC composite, Ceram. Int., 35(2009), No. 4, p. 1677.
15. K.D. Woo, B.R. Kim, E.P. Kwon, D.S. Kang, and I.J. Shon, Properties and rapid consolidation of nanostructured TiC-based hard materials with various binders by a high-frequency induction heated sintering, Ceram. Int., 36(2010), No. 1, p. 351.
16. M. Dewidar, Microstructure and mechanical properties of biocompatible high density Ti-6Al-4V/W produced by high frequency induction heating sintering, Mater. Des., 31(2010), No. 8, p. 3964.
17. 3 reinforced Ni-Fe composite from mechanically alloyed powders by high frequency induction heated sintering, Ceram. Int., 35(2009), No. 8, p. 3147.
18. H.C. Kim, D.K. Kim, K.D. Woo, I.Y. Ko, and I.J. Shon, Consolidation of binderless WC-TiC by high frequency induction heating sintering, Int. J. Refract. Met. Hard Mater., 26(2008), No. 1, p. 48.
19. 2C hard materials by rapid sintering process, Ceram. Int., 34(2008), No. 6, p. 1419.
20. I.J. Shon, I.K. Jeong, I.Y. Ko, J.M. Doh, and K.D. Woo, Sintering behavior and mechanical properties of WC-10Co, WC-10Ni and WC-10Fe hard materials produced by high-frequency induction heated sintering, Ceram. Int., 35(2009), No. 1, p. 339.
21. H.M. Rietveld, A profile refinement method for nuclear and magnetic structures, J. Appl. Crystallogr., 2(1969), No. 2, p. 65.
22. J. Shackelford, W. Alexander, and J. Park, CRC Handbook of Materials Science & Engineering, CRC Press, Boca Raton, 2001.