Computational fluid dynamics simulation of the combustion process, emission formation and the flow field in an in-direct injection diesel engine

Thermal Science

Volumn 17, Issue 1, 2013, Pages 11-23

  Barzegar, Ramin ^a   Shafee, Sina ^b   Khalilarya, Shahram ^c  

^a ISLAMIC AZAD UNIVERSITY   (Iran)

^b MIDDLE EAST TECHNICAL UNIVERSITY   (Turkey)

^c URMIA UNIVERSITY   (Iran)

Author keywords

Combustion; Computational fluid dynamics; Flow field; In direct injection diesel engine; Soot

Indexed keywords

COMBUSTION; COMPUTATIONAL FLUID DYNAMICS; DIESEL ENGINES; DIRECT INJECTION; FUELS; SOOT;

COMBUSTION EMISSIONS; COMBUSTION PRO-CESS; COMPUTATIONAL FLUID DYNAMICS SIMULATIONS; DIRECT INJECTION DIESEL ENGINES; EMISSIONS FORMATION; FULL-LOAD; IN-DIRECT INJECTION DIESEL ENGINE; PART LOAD; SOOT; SWIRL CHAMBERS;

FLOW FIELDS;

EID: 84876985485     PISSN: 03549836     EISSN: None     Source Type: Journal    
DOI: 10.2298/TSCI111218108B     Document Type: Article

References (26)

1. Jafarmadar, S., et al., Numerical Investigation of the Effect of Fuel Injection Mode on Spray-Wall Impingement and Combustion Process in a Direct Injection Diesel Engine at Full Load State, Thermal Science, 14 (2010), 4, pp. 1039-1049, DOI: 10.2298/TSCI10041039J
2. Jafarmadar, S., et al., Modeling the Effect of Spray/Wall Impingement on Combustion Process and Emission in a DI Diesel Engine, Thermal Science, 13 (2009), 3, pp. 23-33, DOI: 10.2298/TSCI0903023J
3. Heywood, J. B., Internal Combustion Engine Fundamental, McGraw Hill, New York, USA, 1988
4. Benson, R. S., Whitehouse, N. D., Internal Combustion Engines, Pergamon Press, Oxford, USA, 1979
5. Ferguson, C. R., Internal Combustion Engines, John Wiley and Sons, New York, USA, 1986
6. Obert, E. F., Internal Combustion Engines and Air Pollution, Intext Education Publ., New York, USA, 1993
7. Patterson, D. J., Henein, N. A., Emissions from Combustion Engines and Their Control, Science Publ., Ann Aebor, Mich., USA, 1972
8. Uludogan, A., et al., Modeling the Effect of Engine Speed on the Combustion Process and Emissions in a DI Diesel Engine, SAE paper 962056, 1996
9. Sanli, A., et al., The Influence of Engine Speed and Load on the Heat Transfer between Gases and In-Cylinder Walls at Fired and Motored Conditions of an IDI Diesel Engine, Applied Thermal Eng., 28 (2008), 11-12, pp. 1395-1404
10. Canakci, M., et al., Combustion Analysis of Preheated Crude Sunflower Oil in an IDI Diesel Engine, Biomass and Bioenergy, 33 (2009), 5, pp. 760-767
11. Selim, M. Y. E., et al., Combustion of Jojoba Methyl Ester in An Indirect Injection Diesel Engine, Renewable Energy, 28 (2003), 9, pp. 1401-1420
12. Celikten, I., An Experimental Investigation of the Effect of the Injection Pressure on Engine Performance and Exhaust Emission in Indirect Injection Diesel Engines, Applied Thermal Eng., 23 (2003), 16, pp. 2051-2060
13. Parlak, A., et al., The Effects of Injection Timing on NOx Emissions of a Low Heat Rejection Indirect Diesel Injection Engine, Applied Thermal Eng., 25 (2005), 17-18, pp. 3042-3052
14. Hotta, Y., et al., Combustion Improvement for Reducing Exhaust Emissions in IDI Diesel Engine, SAE paper 980503, 1998
15. Pinchon, P., Three Dimensional Modeling of Combustion in a Pre-Chamber Diesel Engine, SAE paper 890666, 1989
16. Zellat, M., et al., Three Dimensional Modeling of Combustion and Soot Formation in an Indirect Injection Diesel Engine, SAE paper 900254, 1990
17. Strauss, T. S., Schweimer, G. W., Combustion in a Swirl Chamber Diesel Engine Simulation by Computation of Fluid Dynamics, SAE paper 950280, 1995
18. Strauss, T. S., Schweimer, G. W.,, AVL FIRE user manual, Ver. 8.5, 2006
19. Han, Z., Reitz, R. D., Turbulence Modeling of Internal Combustion Engines Using RNG k-e Models, Combust Sci. and Tech., 106 (1995), 4-6, pp. 267-295
20. Liu, A. B., Reitz, R. D., Modeling the Effects of Drop Drag and Break-up on Fuel Sprays, SAE paper 930072, 1993
21. Dukowicz, J. K., Quasi-Steady Droplet Change in the Presence of Convection, Informal Report Los Alamos Scientific Laboratory, Los Alamos, N. Mex., USA, LA7997-MS
22. Naber, J. D., Reitz, R. D., Modeling Engine Spray/Wall Impingement, SAE paper 880107, 1988
23. Halstead, M., et al., The Auto Ignition of Hydrocarbon Fueled at High Temperatures and Pressures - Fitting of a Mathematical Model, J. Combust Flame, 30 (1977), pp. 45-60
24. Patterson, M. A., et al., Modeling the Effects of Fuel Injection Characteristics on Diesel Engine Soot and NOx Emissions, SAE paper 940523, 1994
25. Mohammahi, A., Ignition of Dual Fuel Engines by Using Free Radicals Existing in EGR Gases, Ph. D. thesis, Faculty of Mechanical Engineering, Tabriz University, Tabriz, Iran 2008
26. Carsten, B., Mixture Formation in Internal Combustion Engines, Springer Publications, Berlin, 2006