Influence of surface roughness on a spray cooling system with R134a. Part I: Heat transfer measurements

Experimental Thermal and Fluid Science

Volumn 46, Issue , 2013, Pages 183-190

  Martínez Galván, Eduardo ^a   Antón, Raúl ^a   Ramos, Juan Carlos ^a   Khodabandeh, Rahmatollah ^b  

^a UNIVERSITY OF NAVARRA   (Spain)

^b ROYAL INSTITUTE OF TECHNOLOGY   (Sweden)

Author keywords

[No Author keywords available]

Indexed keywords

BOILING CURVE; EXPERIMENTAL MEASUREMENTS; HEAT TRANSFER MEASUREMENTS; HEATER TEMPERATURES; SPRAY COOLING; SPRAY PARAMETERS; TEST RIGS; VOLUMETRIC FLOW RATE;

COOLING; HEAT FLUX; NOZZLES; NUCLEATE BOILING; NUSSELT NUMBER; PHASE TRANSITIONS; REFRIGERANTS; SPRAY STEELMAKING; THICKNESS MEASUREMENT;

SURFACE ROUGHNESS;

EID: 84873566092     PISSN: 08941777     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.expthermflusci.2012.12.010     Document Type: Article

References (17)

1. Estes K.A., Mudawar I. Comparison of two-phase electronic cooling using free jets and sprays. Advances in Electronic Packaging, ASME 1995, 10(2):975-987.
2. Chen R.-H., Chow L.C., Navedo J.E. Optimal spray characteristics in water spray cooling. International Journal of Heat and Mass Transfer 2004, 47:5095-5099.
3. Estes K.A., Mudawar I. Correlation of Sauter mean diameter and critical heat flux for spray cooling of small surfaces. International Journal of Heat and Mass Transfer 1995, 38(16):2985-2996.
4. Hsieh S.-S., Tie C.-H. R-134a spray dynamics and impingement cooling in the non-boiling regime. International Journal of Heat and Mass Transfer 2007, 50:502-512.
5. Hsieh S.-S., Fan T.-C., Tsai H.-H. Spray cooling characteristics of water and R-134a. Part I: nucleate boiling. International Journal of Heat and Mass Transfer 2004, 47:5703-5712.
6. Hsieh S.-S., Fan T.-C., Tsai H.-H. Spray cooling characteristics of water and R-134a. Part II: transient cooling. International Journal of Heat and Mass Transfer 2004, 47:5713-5724.
7. Aguilar G., Majaron B., Verkruysse W., Zhou Y., Nelson J.S., Lavernia E.J. Theoretical and experimental analysis of droplet diameter, temperature, and evaporation rate evolution in cryogenic sprays. International Journal of Heat and Mass Transfer 2001, 44:3201-3211.
8. Aguilar G., Vu H., Nelson J.S. Influence of angle between the nozzle and skin surface on the heat flux and overall heat extraction during cryogen spray cooling. Physics in Medicine and Biology 2004, 49:N147-N153.
9. Martinez-Galvan E., Ramos J.C., Anton R., Khodabandeh R. Film thickness and heat transfer measurements in a spray cooling system with R134a. Journal of Electronic Packaging 2011, 133:011002 1-11.
10. Pais M.R., Chow L.C., Mahefkey E.T. Surface roughness and its effects on the heat transfer mechanism in spray cooling. Journal of Heat Transfer 1992, 144:211-219.
11. Sehmbey M.S., Pais M.R., Chow L.C. Effect of surface material properties and surface characteristics in evaporative spray cooling. Journal of Thermophysics and Heat Transfer 1992, 6(3):505-512.
12. Ortiz L., Gonzalez J.E. Experiments on steady-state high heat fluxes using spray cooling. Experimental Heat Transfer 1999, 12(3):215-233.
13. Lee T.-W. Thermal and Flow Measurements, Taylor & Francis Group 2008, Boca Raton.
14. Ghodbane M., Holman J.P. Experimental study of spray cooling with Freon-113. International Journal of Heat and Mass Transfer 1991, 34:1163-1174.
15. Kim J. Spray cooling heat transfer: the state of the art. International Journal Heat and Fluid Flow 2007, 28:753-767.
16. Yang J., Chow L.C., Pais M.R. Nucleate boiling heat transfer in spray cooling. Transactions of the ASME Journal of Heat Transfer 1996, 118:668-671.
17. Visaria M., Mudawar I. Effects of high subcooling on two-phase spray cooling and critical heat flux. International Journal of Heat and Mass Transfe 2008, 51:5269-5278.