Effects of high subcooling on two-phase spray cooling and critical heat flux

International Journal of Heat and Mass Transfer

Volumn 51, Issue 21-22, 2008, Pages 5269-5278

  Visaria, Milan ^a   Mudawar, Issam ^a  

^a PURDUE UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; HEATING EQUIPMENT; NOZZLES; PESTICIDES;

CRITICAL HEAT FLUX; SPRAY PERFORMANCE; SUB-COOLING;

HEAT FLUX;

EID: 51349117634     PISSN: 00179310     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijheatmasstransfer.2008.02.045     Document Type: Article

References (17)

1. Mudawar I. Assessment of high-heat-flux thermal management schemes. IEEE Trans. - Comp. Packag. Technol. 24 (2001) 122-141
2. Toda S. A study in mist cooling (1st report: investigation of mist cooling). Trans. Jpn. Soc. Mech. Eng. 38 (1972) 581-588
3. Mudawar I., and Valentine W.S. Determination of the local quench curve for spray-cooled metallic surfaces. J. Heat Treating 7 (1989) 107-121
4. Monde M. Critical heat flux in saturated forced convection boiling on a heated disk with impinging droplets. Trans. Jpn. Soc. Mech. Eng. 8 (1979) 54-64
5. Toda S., and Uchida H. Study of liquid film cooling with evaporation and boiling. Trans. Jpn. Soc. Mech. Eng. 2 (1973) 44-62
6. Estes K.A., and Mudawar I. Correlation of Sauter mean diameter and critical heat flux for spray cooling of small surfaces. Int. J. Heat Mass Transfer 38 (1995) 2985-2996
7. Mudawar I., and Estes K.A. Optimizing and predicting CHF in spray cooling of a square surface. J. Heat Transfer 118 (1996) 672-680
8. C.S.K. Cho, K. Wu, Comparison of burnout characteristics in jet impingement cooling and spray cooling, in: Proceedings of National Heat Transfer Conference, vol. 1, Houston, Texas, 1988, pp. 561-567.
9. Chen R.-H., Chow L.C., and Navedo J.E. Effects of spray characteristics on critical heat flux in subcooled water spray cooling. Int. J. Heat Mass Transfer 45 (2002) 4033-4043
10. Rybicki J.R., and Mudawar I. Single-phase and two-phase cooling characteristics of upward-facing and downward-facing sprays. Int. J. Heat Mass Transfer 49 (2006) 5-16
11. Visaria M., and Mudawar I. Theoretical and experimental study of the effects of spray inclination on two-phase spray cooling and critical heat flux. Int. J. Heat Mass Transfer 51 (2008) 2398-2410
12. Visaria M., and Mudawar I. A systematic approach to predicting critical heat flux for inclined sprays. J. Heat Transfer J. Electron. Packaging 129 (2007) 452-459
13. Lin L., and Ponnappan R. Heat transfer characteristics of spray cooling in a closed loop. Int. J. Heat Mass Transfer 46 (2003) 3737-3746
14. Pautsch A.G., and Shedd T.A. Spray impingement cooling with single- and multiple-nozzle arrays. Part I: heat transfer data using FC-72. Int. J. Heat Mass Transfer 48 (2005) 3167-3175
15. Sehmbey M.S., Pais M.R., and Chow L.C. Effect of surface material properties and surface characteristics in evaporative spray cooling. J. Thermophys. Heat Transfer 6 (1992) 505-512
16. E.A. Silk, J. Kim, K. Kiger, Effect of spray cooling trajectory on heat flux for a straight finned enhanced surface, in: Proceedings of National Heat Transfer Summer Conference, Paper HT2005-72634, San francisco, California, 2005.
17. Li B.Q., Cader T., Schwarzkopf J., Okamoto K., and Ramaprian B. Spray angle effect during spray cooling of microelectronics: experimental measurements and comparison with inverse calculations. Appl. Therm. Eng. 26 (2006) 1788-1795