A method for evaluating dynamical friction in linear ball bearings

Sensors (Switzerland)

Volumn 10, Issue 11, 2010, Pages 10069-10080

  Fujii, Yusaku ^a   Maru, Koichi ^a   Jin, Tao ^a   Yupapin, Preecha P ^b   Mitatha, Somsak ^b  

^a GUNMA UNIVERSITY   (Japan)

^b KING MONGKUT'S INSTITUTE OF TECHNOLOGY LADKRABANG   (Thailand)

Author keywords

Dynamic friction coefficient; Inertial force; Linear ball bearings; Optical measurement

Indexed keywords

CENTRE OF GRAVITY; DYNAMIC FRICTION COEFFICIENT; DYNAMICAL FRICTIONS; INERTIAL FORCES; LINEAR BALL BEARING; LINEAR BEARINGS; OPTICAL INTERFEROMETER; OPTICAL MEASUREMENT;

BALL BEARINGS; GRAVITATION; OPTICAL DATA PROCESSING;

FRICTION;

ARTICLE; FRICTION; INTERFEROMETRY; OPTICAL INSTRUMENTATION;

FRICTION; INTERFEROMETRY; OPTICAL DEVICES;

EID: 84871051377     PISSN: 14248220     EISSN: None     Source Type: Journal    
DOI: 10.3390/s101110069     Document Type: Article

References (21)

1. Durak, E.; Kurbanolu, C.; Bi{dotless}yi{dotless}kli{dotless}olu, A.; Kaleli, H. Measurement of friction force and effects of oil fortifier in engine journal bearings under dynamic loading conditions. Tribol. Int. 2003, 36, 599-607
2. Ünlü, B.; Atik, E. Determination of friction coefficient in journal bearings. Mater. Design 2007, 28, 973-977.
3. Yao, Z.; Zhang, Q.; Tao, Y.; Zhang, X. A new approach to measure the friction coefficient of micro journal bearings. Tribol. Int. 2000, 33, 485-489.
4. Budinski, K. An inclined plane test for the breakaway coefficient of rolling friction of rolling element bearings. Wear 2005, 259, 1443-1447.
5. Fujii, Y. A method for calibrating force transducers against oscillation force. Meas. Sci. Technol. 2003, 14, 1259-1264.
6. Fujii, Y. Method for correcting the effect of the inertial mass on dynamic force measurements. Meas. Sci. Technol. 2007, 18, N13-N20.
7. Kumme, R.; Dixon, M. The results of comparisons between two different dynamic force measurement systems. Measurement 1992, 10, 140-144.
8. Kumme, R. Investigation of the comparison method for the dynamic calibration of force transducers. Measurement 1998, 23, 239-245.
9. Park, Y.K.; Kumme, R.; Kang, D.I. Dynamic investigation of a three-component force-moment sensor. Meas. Sci. Technol. 2002, 13, 654-659.
10. Park, Y.K.; Kumme, R.; Kang, D.I. Dynamic investigation of a binocular six-component force-moment sensor. Meas. Sci. Technol. 2002, 13, 1311-1318.
11. Li, Y.F.; Chen, X.B. On the dynamic behavior of a force/torque sensor for robots. IEEE Trans. Instrum. Meas. 1998, 47, 304-308.
12. Xu, K.J.; Jia, L. One-stage identification algorithm and two-step compensation method of Hammerstein model with application to wrist force sensor. Rev. Sci. Instrum. 2002, 73, 1949-1955.
13. Fujii, Y. Method of evaluating the dynamic response of materials to forced oscillation. Meas. Sci. Technol. 2006, 17, 1935-1940.
14. Fujii, Y. Microforce materials tester based on the levitation mass method. Meas. Sci. Technol. 2007, 18, 1678-1682.
15. Fujii, Y. Method of generating and measuring static small force using down-slope component of gravity. Rev. Sci. Instrum. 2007, 78, 066104-1-3.
16. Fujii, Y. Measurement of force acting on a moving part of a pneumatic linear bearing. Rev. Sci. Instrum. 2003, 74, 3137-3141.
17. Fujii, Y. Frictional characteristics of an aerostatic linear bearing. Tribol. Int. 2006, 39, 888-896.
18. Fujii, Y. An optical method for evaluating frictional characteristics of linear bearings. Opt. Laser. Eng. 2004, 42, 493-501.
19. Baumeister, T.; Marks, L.S. Standard Handbook for Mechanical Engineers, 7th ed.; McGraw-Hill: New York, NY, USA, 1967; pp. 6-40.
20. Fujii, Y.; Valera, J. Impact force measurement using an inertial mass and a digitizer. Meas. Sci. Technol. 2006, 17, 863-868.
21. Fujii, Y. Impact response measurement of an accelerometer. Mech. Syst. Signal. Proceed. 2007, 21, 2072-2079.