Experimental investigation on punching strength and deformation capacity of shear-reinforced slabs

ACI Structural Journal

Volumn 109, Issue 6, 2012, Pages 889-900

  Lips, Stefan ^a   Ruiz, Miguel Fernández ^a   Muttoni, Aurelio ^a  

^a EPFL   (Switzerland)

Author keywords

Critical shear crack theory; Deformation capacity; Flat slabs; Punching shear; Shear reinforcement

Indexed keywords

CRITICAL SHEAR CRACK THEORIES; DEFORMATION CAPACITY; FLAT SLABS; PUNCHING SHEAR; SHEAR REINFORCEMENT;

CRACKS; REINFORCEMENT;

COLUMNS (STRUCTURAL);

EID: 84868101814     PISSN: 08893241     EISSN: None     Source Type: Journal    
DOI: None     Document Type: Article

References (24)

1. Fernández Ruiz, M.; Fürst, A.; Guandalini, S.; Hunkeler, F.; Moser, K.; Muttoni, A.; and Seiler, H., "Sécurité structurale des parkings couverts (Structural Safety of Parking Garages)," Documentation SIA D0226, Zurich, Switzerland, 2008, 105 pp. (in French)
2. fb (CEB-FIP), "fb Bulletin 56: Model Code 2010, First Complete Draft," V. 2, Lausanne, Switzerland, Apr. 2010, 288 pp.
3. Fernández Ruiz, M., and Muttoni, A., "Application of Critical Shear Crack Theory to Punching of Reinforced Concrete Slabs with Transverse Reinforcement," ACI Structural Journal, V. 106, No. 4, July-Aug. 2009, pp. 485-494.
4. Guandalini, S.; Burdet, O. L.; and Muttoni, A., "Punching Tests of Slabs with Low Reinforcement Ratios," ACI Structural Journal, V. 106, No. 1, Jan.-Feb. 2009, pp. 87-95.
5. Hawkins, N. M., "Shear Strength of Slabs with Shear Reinforcement," Shear in Reinforced Concrete, SP-42, American Concrete Institute, Farm-ington Hills, MI, 1974, pp. 785-815.
6. Seible, F.; Ghali, A.; and Dilger, W. H., "Preassembled Shear Reinforcing Units for Flat Plates," ACI JOURNAL, Proceedings V. 77, No. 1, Jan.-Feb. 1980, pp. 28-35. (Pubitemid 10450526)
7. Van der Voet, F.; Dilger, W. H.; and Ghali, A., "Concrete Flat Plates with Well-Anchored Shear Reinforcement Elements," Canadian Journal of Civil Engineering, V. 9, No. 1, 1981, pp. 107-114.
8. Elgabry, A. A., and Ghali, A., "Design of Stud-Shear Reinforcement for Slabs," ACI Structural Journal, V. 87, No. 3, May-June 1990, pp. 350-361. (Pubitemid 20696660)
9. Regan, P. E., and Samadian, F., "Shear Reinforcement against Punching in Reinforced Concrete Flat Slabs," The Structural Engineer, V. 79, No. 10, 2001, pp. 24-31. (Pubitemid 32492092)
10. Gomes, R. B., and Regan, P. E., "Punching Strength of Slabs Reinforced for Shear with Offcuts of Rolled Steel I-Section Beams," Magazine of Concrete Research, V. 51, No. 2, 1999, pp. 121-129.
11. Birkle, G., "Punching of Flat Slabs: The Infuence of Slab Thickness and Stud Layout," PhD thesis, University of Calgary, Calgary, AB, Canada, 2004, 152 pp.
12. Beutel, R., and Hegger, J., "The Effect of Anchorage on the Effectiveness of the Shear Reinforcement in the Punching Zone," Cement and Concrete Composites, V. 24, No. 6, 2002, pp. 539-549.
13. Hegger, J.; Walraven, J. C.; and Häusler, F., "Zum Durchstanzen von Flachdecken nach Eurocode 2 (Punching of Flat Slabs According to Eurocode 2)," Beton-und Stahlbetonbau, V. 105, No. 4, 2010, pp. 206-215. (in German)
14. Dechka, D. C., "Response of Shear-Stud-Reinforced Continuous Slab-Column Frames to Seismic Loads," PhD thesis, University of Calgary, Calgary, AB, Canada, 2001, 472 pp.
15. ACI Committee 318, "Building Code Requirements for Structural Concrete (ACI 318-08) and Commentary," American Concrete Institute, Farmington Hills, MI, 2008, 473 pp.
16. EN 1992-1-1, "Eurocode 2: Design of Concrete Structures\Part 1-1: General Rules and Rules for Buildings," CEN, Brussels, Belgium, 2004, 225 pp.
17. Muttoni, A., and Fernández Ruiz, M., "MC2010: The Critical Shear Crack Theory as a Mechanical Model for Punching Shear Design and Its Application to Code Provisions," fb Bulletin 57, Lausanne, Switzerland, 2010, pp. 31-60.
18. Fernández Ruiz, M.; Muttoni, A.; and Kunz, J., "Strengthening of Flat Slabs against Punching Shear Using Post-Installed Shear Reinforcement," ACI Structural Journal, V. 107, No. 4, July-Aug. 2010, pp. 434-442.
19. Fernández Ruiz, M., and Muttoni, A., "Performance and Design of Punching Shear Reinforcing Systems," 3rd International fb Congress, No. 437, Washington, DC, 2010, 15 pp.
20. Dilger, W. H.; Birkle, G.; and Mitchell, D., "Effect of Flexural Reinforcement on Punching Shear Resistance," Punching Shear in Reinforced Concrete Slabs, SP-232, M. A. Polak and ACI Committee 445, eds., American Concrete Institute, Farmington Hills, MI, 2005, pp. 57-74.
21. Birkle, G., and Dilger, W. H., "Shear Strength of Slabs with Double-Headed Shear Studs in Radial and Orthogonal Layouts," Thomas T.C. Hsu Symposium: Shear and Torsion in Concrete Structures, SP-265, A. Belarbi, Y. L. Mo, and A. Ayoub, eds., American Concrete Institute, Farmington Hills, MI, 2009, pp. 499-510.
22. Vollum, R. L.; Abdel-Fattah, T.; Eder, M.; and Elghazouli, A. Y., "Design of ACI-Type Punching Shear Reinforcement to Eurocode 2," Magazine of Concrete Research, V. 62, No. 1, 2010, pp. 3-16.
23. Muttoni, A., "Punching Shear Strength of Reinforced Concrete Slabs without Transverse Reinforcement," ACI Structural Journal, V. 105, No. 4, July-Aug. 2008, pp. 440-450.
24. Birkle, G., and Dilger, W. H., "Infuence of Slab Thickness on Punching Shear Strength," ACI Structural Journal, V. 105, No. 2, Mar.-Apr. 2008, pp. 180-188. (Pubitemid 351513097)