Optimization of surface roughness in turning unidirectional glass fiber reinforced plastics (UD-GFRP) composites using polycrystalline diamond (PCD) cutting tool

Indian Journal of Engineering and Materials Sciences

Volumn 19, Issue 3, 2012, Pages 163-174

  Kumar, Surinder ^a   Meenu, ^a   Satsangi, P S ^b   Sardana, H K ^c  

^a NATIONAL INSTITUTE OF TECHNOLOGY   (India)

^b PEC UNIVERSITY OF TECHNOLOGY   (India)

^c CSIR CENTRAL SCIENTIFIC INSTRUMENTS ORGANISATION   (India)

Author keywords

ANOVA; Cutting parameters; Machining; Optimization; Polycrystalline diamond (PCD) tool; Response table; Surface roughness; Taguchi method; Turning; UD GFRP composites

Indexed keywords

EID: 84864245715     PISSN: 09714588     EISSN: 09751017     Source Type: Journal    
DOI: None     Document Type: Article

References (36)

1. Santhanakrishnan G, Krishnamurthy R & Malhotra S K, Wear, 132 (1989) 327-336.
2. Santhanakrishnan G, Krishnamurthy R & Malhotra S K, J Mech Work Technol, 17 (1988) 195-204.
3. Evestine G C & Rogers T G, J Comp Mater, 5 (1971) 94-105.
4. Konig W, Wulf CH, Grab & Willerscheid H, CIRP Ann, 34 (1985) 537-548.
5. Davim J P & Reis P, Int J Manuf Technol Manage, 6(1/2) (2004) 185-197.
6. Sreejith P S, Krishnamoorthy R, Narayanasamy K & Malhotra S K, J Mater Process Technol, 88 (1999) 43-50.
7. Palanikumar K, J Reinf Plast Compos, 25 (2006) 1739-1751.
8. An S O, Lee E S & Noh S L, J Mater Process Technol, 68 (1997) 60-67.
9. Palanikumar K, Karunamoorthy L & Karthikeyan R, Mater Manuf Process, 21 (2006) 846-852.
10. Sreejith P S, Krishnamoorthy R & Malhotra S K, J Mater Process Technol, 183 (2007) 88-95.
11. Davim J P & Mata F, Int J Adv Manuf Technol, 26 (2005) 319-323.
12. Davim J P & Mata F, Mater Des, 28 (2007) 1050-1054.
13. Palanikumar K, Mater Des, 28 (2007) 2611-2618.
14. Hussain S A, Pandurangadu V & Palanikumar K, Eur J Sci Res, 41(1) (2010) 84-98.
15. Palanikumar K, Int J Adv Manuf Technol, 36 (2008) 19-27.
16. Yusuf Sahin & Riza Motorcu A, Am J Appl Sci, 1(1) (2004) 12-17.
17. Davim J P, J Mater Process Technol, 116 (2001) 305-308.
18. Aravindan S, Naveen Sait A & Noorul Haq A, Int J Adv Manuf Technol, 37 (2008) 1069-1081.
19. Khan M & Adam Kumar A, J Manuf Process, 13 (2011) 67-73.
20. Rajasekaran T, Palanikumar K & Vinayagam B K, Prod Eng Res Dev, 5 (2011) 191-199.
21. Sakuma By Keizo & Seto Masafumi, Bull JSME, 26(218) (1983) 1420-1427.
22. Fereirra J R, Coppini N L & Levy Neto, J Mater Process Technol, 109 (2001) 65-71.
23. Spur G & Wunsch U E, Manuf Rev, 1(2) (1988) 24-129.
24. Palanikumar K, Karunamoorthy L & Karthikeyan R, Mater Des, 27 (2006) 862-871.
25. Palanikumar K, Karunamoorthy L, Karthikeyan R & Latha B, Met Mater Int, 12(6) (2006) 483-491.
26. Naveen Sait A, Aravindan S & Noorul Haq A, Adv Prod Eng Manage, 4 (2009) 47-58.
27. Hussain S A, Pandurangadu V & Palanikumar K, Int J Eng Sci Technol, 4 (2011) 103-118
28. Santhanakrishnan G, Investigations on machining of FRP composites and their tribological behaviour, Ph.D. Thesis, IIT Madras, Chennai, India; 1990.
29. Jahanmir S, Ramulu M & Koshy, Machining of Ceramics and Composites (Dekker, New York, NY) 1998, 238-243.
30. Bagci E, & Isi{dotless}k B, Int J Adv Manuf Technol, 31 (2006) 10-17.
31. Hussain S A, Pandurangadu V, Palanikumar K & Bharathi V V, Jordan J Mech Ind Eng, 5(5) (2011) 433-438
32. Harvey K & Ansell Martin P, Improved timber connections using bonded-in GFRP rods, Department of Materials Science and Engineering, University of Bath, Bath, UK, 2000.
33. Feng C X & Wang X F, IIE Trans, 35 (2003) 11-27.
34. Kopac J, Bahor M & Sokovi C M, Int J Mach Tools Manuf, 42(6) (2002) 707-716.
35. Phadke M S, Quality Engineering Using Robust Design (Prentice-Hall, Englewood Cliffs, NJ), 1989.
36. Ross P J, Taguchi techniques for quality engineering (McGraw-Hill, New York), 1996.