Experimental characterization of friction coefficient at the tool-chip-workpiece interface during dry cutting of AISI 1045

Wear

Volumn 286-287, Issue , 2012, Pages 108-115

  Ben Abdelali, H ^a,b,c   Claudin, C ^a   Rech, J ^a   Ben Salem, W ^b   Kapsa, Ph ^c   Dogui, A ^b  

^a UNIVERSITÉ DE LYON   (France)

^b UNIVERSITY OF MONASTIR   (Tunisia)

^c LABORATOIRE DE TRIBOLOGIE ET DYNAMIQUE DES SYSTÈMES   (France)

Author keywords

Cutting; Friction; Heat partition; Sliding velocity

Indexed keywords

AISI 1045; CONTACT PRESSURES; DRY CUTTING; EXPERIMENTAL CHARACTERIZATION; EXPERIMENTAL SETUP; FRICTION COEFFICIENTS; FRICTION REGIME; HEAT PARTITIONS; HIGH SLIDING VELOCITIES; LOW SLIDING VELOCITIES; SLIDING VELOCITIES; TIN COATED CARBIDE;

CUTTING; CUTTING TOOLS; FRICTION; METAL CUTTING; PLASTICS FILLERS; STAINLESS STEEL; TITANIUM NITRIDE;

HEAT FLUX;

EID: 84860632912     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2011.05.030     Document Type: Article

References (25)

1. Ruiz de Eguilaz E., Rech J., Arrazola P. Characterization of friction coefficient and heat partition coefficient between an AISI 4140 steel and a TiN-coated carbide - influence of (Ca, Mn, S) steel's inclusions. J. Eng. Tribol. 2010, 224(J10):1115-1127.
2. Buryta D., Sowerby R., Yellowley I. Stress distributions on the rake face during orthogonal machining. Int. J. Mach. Tool. Manu. 1994, 34(5):721-739.
3. Rech J. A multi-view approach to the tribological characterization of cutting tool coatings for steels in high velocity dry turning. Int. J. Mach. Machinability Mater. 2006, 1:27-44.
4. Trent E.M. Metal Cutting 1991, Butterworth Heinemann, ISBN 0-7506-1068-9.
5. M'Saoubi R., Chandrasekaran H. Innovative methods of the investigation of tool-chip adhesion and layer formation during machining. Ann. CIRP 2005, 54(1):59-62.
6. Kilic D.S., Raman S. Observations of the tool-chip boundary conditions in turning of aluminium alloys. Wear 2007, 262:889-904.
7. Arrazola P.J., Ugarte D., Domi{dotless}inguez X. A new approach for the friction identification machining through the use of finite element modeling. Int. J. Mach. Tool. Manu. 2008, 48:173-183.
8. Grzesik W., Zalisz Z., Nieslony P. Friction and wear testing of multilayer coatings on carbide substrates for dry machining applications. Surf. Coat. Technol. 2002, 155:37-45.
9. Olsson M., Soderberg S., Jacobson S., Hogmark S. Simulation of cutting pin-on-disc test. Int. J. Mach. Tool. Manu. 1989, 29:377-390.
10. Meiller M., Lebrun J.L., Touratier M., Ryckelynck D. Friction law for tool workpiece contact area in dry machining. Proceedings of the International Workshop on Friction and Flow Stress in Cutting and Forming 2000, 101-109.
11. Zemzemi F., Rech J., Ben Salem W., Kapsa P., Dogui A. Development of a friction model for the tool-chip-workpiece interface during dry machining of AISI 4142 steel with TiN coated carbide cutting tools. Int. J. Mach. Machinability Mater. 2007, 2(3-4):361-367.
12. Hedenquist P., Olsson M. Sliding wear testing of coated cutting tool materials. Tribol. Int. 1991, 23(3):143-150.
13. Bonnet C., Valiorgue F., Rech J., Claudin C., Hamdi H., Bergheau J.M., Gilles P. Identification of a friction model - application to the context of dry cutting of an AISI 316L austenitic stainless steel with a TiN coated carbide tool. Int. J. Mach. Tool. Manu. 2008, 48:1211-1223.
14. Rech J., Claudin C., D'Eramo E. Identification of a friction model - application to the context of dry cutting of an AISI 1045 annealed steel with a TiN-coated carbide tool. Tribol. Int. 2009, 42:738-744.
15. Ozel T. The influence of friction models on finite element simulations of machining. Int. J. Mach. Tool. Manu. 2006, 46:518-530.
16. Moufki A., Molinari A., Duzinski D. Modeling of orthogonal cutting with temperature dependant friction law. J. Mech. Phys. Solids 1998, 46:2103-2138.
17. Zemzemi F., Rech J., Ben Salem W., Kapsa P., Dogui A. Identification of a friction model at tool/chip/workpiece interfaces in dry machining of AISI 4142 treated steels. J. Mater. Process. Technol. 2009, 209:3978-3990.
18. Zemzemi F., Ben Salem W., Rech J., Kapsa P., Dogui A. New tribometer designed for the characterization of the friction properties at the tool/chip/workpiece interfaces in machining. Tribotest 2008, 14:11-25.
19. Rech J., Kusiak A., Battaglia J.L. Tribological and thermal functions of cutting tool coatings. Surf. Coat. Technol. 2004, 186:364-371.
20. Kusiak A., Battaglia J.L., Rech J. Tool coatings influence on the heat transfer in the tool during machining. Surf. Coat. Technol. 2005, 195:29-40.
21. Challen J.M., Oxley P.L.B. An explanation of the different regimes of friction and wear using asperity deformation models. Wear 1979, 53:229-243.
22. He L., Ovaert T.C. Heat partitioning coefficient calculations for sliding contacts with friction. Tribol. Trans. 2008, 51:12-18.
23. Grzesik W. Advanced Machining Processes of Metallic Materials 2008, Elsevier.
24. C. Vergne, Analyse de l'influence des oxydes dans le frottement d'une fonte pour outil de travail à chaud. PhD thesis, Ecole des Mines de Paris, 2001.
25. H. Ben Abdelali, C. Courbon, J. Rech, W. Ben Salem, A. Dogui and Ph. Kapsa, Identification of a friction model at the tool-chip-workpiece interface in dry machining of a AISI 1045 steel with a TiN coated carbide tool, ASME-J. Tribol., submitted for publication.