Analysis of hot deformation behavior of Al 5083-TiC nanocomposite using constitutive and dynamic material models

Materials and Design

Volumn 37, Issue , 2012, Pages 102-110

  Senthilkumar, V ^a   Balaji, A ^a   Narayanasamy, R ^a  

^a NATIONAL INSTITUTE OF TECHNOLOGY   (India)

Author keywords

A. Nano material; C. Forming; F. Microstructure

Indexed keywords

ADIABATIC SHEAR BAND FORMATION; CONTROL PARAMETERS; CONTROL PROCESS; DEFORMATION MECHANISM; DYNAMIC MATERIAL MODELS; DYNAMIC RECOVERY; F. MICROSTRUCTURE; FLOW LOCALIZATION; HOT DEFORMATION BEHAVIORS; MICRO-STRUCTURAL; MICROSTRUCTURAL FEATURES; NANOCOMPOSITE SAMPLES; PROCESSING MAPS; TEMPERATURE RANGE;

ALUMINUM; BEHAVIORAL RESEARCH; DEFORMATION; DYNAMIC RECRYSTALLIZATION; HOT WORKING; MICROSTRUCTURAL EVOLUTION; NANOCOMPOSITES; TITANIUM CARBIDE;

STRAIN RATE;

EID: 84856092720     PISSN: 02641275     EISSN: 18734197     Source Type: Journal    
DOI: 10.1016/j.matdes.2011.12.049     Document Type: Article

References (26)

1. Hassan S.F., Gupta M. Development of high strength magnesium copper based hybrid composites with enhanced tensile properties. Compos Struct 2006, 72:19-26.
2. Laha T., Chen Y., Lahiri D., Agarwal A. Tensile properties of carbon nanotube reinforced aluminum nanocomposite fabricated by plasma spray forming. Composites A 2009, 40:589-594.
3. Santos-Beltrán A., Gallegos-Orozco V., Goytia Reyes R., Miki-Yoshida M., Estrada-Guel I., Martínez-Sánchez Mechanical and microstructural characterization of dispersion strengthened Al-C system nanocomposites. J Alloys Compd 2010, 489:626-630.
4. Srinivasan N., Prasad Y.V.R.K., Rama Rao P. Hot deformation behaviour of Mg-3Al alloy - a study using processing map. Mater Sci Eng A 2008, 476:146-156.
5. Raghunath B.K., Karthikeyan R., Ganesan G., Gupta M. An investigation of hot deformation response of particulate-reinforced magnesium +9% titanium composite. Mater Des 2008, 29:622-627.
6. Bardi F., Cabibbo M., Evangelista E., Spigarelli S., Vukčevič M. An analysis of hot deformation of an Al-Cu-Mg alloy produced by powder metallurgy. Mater Sci Eng A 2003, 339:43-52.
7. Byung-Chul Ko, Yeon-Chul Yoo Prediction of dynamic recrystallization condition by deformation efficiency for Al 2024 composite reinforced with SiC particle. J Mater Sci 2000, 35:4073-4077.
8. Radhakrishna Bhat B.V., Mahajan Y.R., Prasad Y.V.R.K. Effect of volume fraction of SiCp reinforcement on the processing maps for 2124 Al matrix composites. Mater Trans A 2000, 31:629.
9. Dejun Li, Yaorong Feng, Zhifu Yin, Fengshou Shangguan, Ke Wang, Qiang Liu, et al. Hot deformation behavior of an austenitic Fe-20Mn-3Si-3Al transformation induced plasticity steel. Mater Des 2012, 34:713-718.
10. Cavaliere P. Isothermal forging of AA2618 reinforced with 20% of alumina particles. Composites A 2004, 35:619-629.
11. Lin Y.C., Chen Xiao-Min A critical review of experimental results and constitutive descriptions for metals and alloys in hot working. Mater Des 2011, 32:1733-1759.
12. 33w/AZ91D composite during hot compression and its validation. Comput Mater Sci 2011, 50:2422-2426.
13. Prasad Y.V.R.K, Sasidhara S. Hot working guide: a compendium of processing maps 1997, ASM International, Materials Park, Ohio.
14. Prasad Y.V.R.K., Sastry D.H., Deevi S.C. Processing maps for hot working of a P/M iron aluminide alloy. Intermetallics 2000, 8:1067-1074.
15. Narayana Murthy S.V.S., Nageswara Rao B., Kashyap B.P. Instability criteria for hot deformation of materials. Int Mater Rev 2000, 41:15-26.
16. 3 composites. Mater Sci Eng A 2009, 518:61-64.
17. Tun K.S., Gupta M. Development of magnesium/(yttria+nickel) hybrid nanocomposites using hybrid microwave sintering: microstructure and tensile properties. J Alloys Compd 2009, 487:76-82.
18. Hassan S.F., Gupta M. Strain rate effects on the mechanical properties of a Fe-Mn-Al alloy under dynamic impact deformations. Mater Sci Eng A 2005, 392:163-168.
19. Shao J.C., Xiao B.L., Wang Q.Z., Liu Y., Yang K. Constitutive flow behavior and hot workability of powder metallurgy processed 20vol% SiCp/2024Al composite. Mater sci eng A 2010, 7865-7872.
20. Hosseinipour S.J. An investigation into hot deformation of aluminum alloy 5083. Mater Des 2009, 30:319-322.
21. Rokni M.R., Zarei-Hanzaki A., Roostaei Ali A., Abedi H.R. An investigation into the hot deformation characteristics of 7075 aluminum alloy. Mater Des 2011, 32:2339-2344.
22. Zhang Jing, Chen Boquan, Baoxiang Zhang Effect of initial microstructure on the hot compression deformation behavior of a 2219 aluminum alloy. Mater Des 2012, 34:15-21.
23. Rao K.P., Prasad Y.V.R.K., Suresh K. Hot working behavior and processing map of a γ-TiAl alloy synthesized by powder metallurgy. Mater Des 2011, 32:4874-4881.
24. Gang Meng, Bolang Li, Hongmei Li, Hui Huang, Zuoren Nei Hot deformation and Processing maps of an Al-5.7%wt Mg alloy with erbium. Mater Sci Eng A 2009, 517:132-137.
25. Poliak E.I., Jonas J.J. Initiation of dynamic recrystallization in constant strain rate hot deformation. ISIJ Int 2003, 426-432:57-66.
26. 3 composite. Compos Sci Technol 2009, 69:1070-1076.