A new thermomechanical model of cutting applied to turning operations. Part II. Parametric study

International Journal of Machine Tools and Manufacture

Volumn 45, Issue 2, 2005, Pages 181-193

  Moufki, A ^a   Molinari, A ^a  

^a UNIVERSITÉ DE LORRAINE   (France)

Author keywords

Bar turning; Chip flow direction; Cutting edge geometry; Cutting forces; Dynamic friction; Machining; Thermoviscoplastic behavior; Tool heating

Indexed keywords

CUTTING; FRICTION; HEATING; MATHEMATICAL MODELS; THERMOMECHANICAL TREATMENT; VISCOPLASTICITY;

BAR TURNING; CHIP FLOW DIRECTION; CUTTING EDGE GEOMETRY; CUTTING FORCES; DYNAMIC FRICTION; THERMOVISCOPLASTIC BEHAVIOR; TOOL HEATING;

MACHINING;

EID: 8344222803     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijmachtools.2004.07.005     Document Type: Article

References (17)

1. A. Molinari, A. Moufki, A new thermomechanical model of cutting applied to turning operations. Part I - Theory., Int. J. Mach. Tools Manufact. (this issue).
2. A. Moufki, D. Dudzinski, A. Molinari, M. Rausch, Thermoviscoplastic modelling of oblique cutting: forces and chip flow predictions, Int. J. Mech. Sci. 42 (2000) 1205-1232.
3. A. Moufki, A. Devillez, D. Dudzinski, A. Molinari, Thermomechanical modelling of oblique cutting and experimental validation, Int. J. Mach. Tools Manufact. 44 (9) (2004) 971-989.
4. A. Molinari, A. Moufki, D. Dudzinski, Etude du comportement du 42CD4, Final Technical Report, CREAS Ascomeatal, 1997.
5. A. Moufki, A. Molinari, D. Dudzinski, Modelling of orthogonal cutting with a temperature dependent friction law, J. Mech. Phys. Solids 46 (10) (1998) 2103-2138.
6. A. Moufki, A. Devillez, D. Dudzinski, A. Molinari, Thermomechanical modelling of cutting and experimental validation, in: D. Dudzinski, A. Molinari, H. Schulz (Eds.), Metal Cutting and High Speed Machining, Kluwer Academic, Dordrecht, 2002, pp. 51-68.
7. M.C. Shaw, Metal Cutting Principles, Oxford Science, Oxford, 1984.
8. T.I. El-Wardany, E. Mohammed, M.A. Elbestawi, Cutting temperature of ceramic tools in high speed machining of difficult-to-cut materials, Int. J. Mach. Tools Manufact. 36 (5) (1996) 611-634.
9. H.A. Kishawy, M.A. Elbestawi, Effects of process parameters on material side flow during hard turning, Int. J. Mach. Tools Manufact. 39 (1999) 1017-1030.
10. H.T. Young, P. Mathew, P.L.B. Oxley, Allowing for nose radius effects in predicting the chip flow direction and cutting forces in bar turning, Proc. Inst. Mech. Engrs 201 (C3) (1987) 213-226.
11. J.A. Arsecularatne, P. Mathew, P.L.B. Oxley, Prediction of chip flow direction and cutting forces in oblique machining with nose radius tools, Proc. Inst. Mech. Engrs 209 (1995) 305-315.
12. J.A. Arsecularatne, R.F. Fowle, P. Mathew, Prediction of chip flow direction, cutting forces and surface roughness in finish turning, J. Manufact. Sci. Eng. 120 (1998) 1-12.
13. J.S. Strenkowski, A.I. Shih, J.C. Lin, An analytical finite element model for predicting three-dimensional tool forces and chip low, Int. J. Mach. Tools Manufact. 42 (2002) 723-731.
14. L.V. Colwell, Predicting the angle of chip flow for single-point cutting tools, Trans. ASME 76 (1954) 199-204.
15. K. Okushima, K. Minato, On the behavior of chip in steel cutting, Bull. Jpn. Soc. Mech. Engrs 2 (5) (1959) 58-64.
16. N. Narutaki, Y. Yamane, K. Hayashi, T. Kitagawa, High speed machining of Inconel 718 with ceramic tools, Ann. CIRP 42 (1993) 103-106.
17. M. Rahman, W.K.H. Seah, T.T. Teo, The machinability of Inconel 718, J. Mater. Process. Technol. 63 (1997) 199-204.