A new thermomechanical model of cutting applied to turning operations. Part I. Theory

International Journal of Machine Tools and Manufacture

Volumn 45, Issue 2, 2005, Pages 166-180

  Molinari, A ^a   Moufki, A ^a  

^a UNIVERSITÉ DE LORRAINE   (France)

Author keywords

Bar turning; Chip flow direction; Cutting edge geometry; Cutting forces; Dynamic friction; Machining; Thermoviscoplastic behavior; Tool heating

Indexed keywords

FRICTION; HEATING; INTERFACES (MATERIALS); MACHINING; STRAIN HARDENING; TEMPERATURE DISTRIBUTION; THERMOMECHANICAL TREATMENT; VISCOPLASTICITY;

BAR TURNING; CHIP FLOW DIRECTION; CUTTING EDGE GEOMETRY; CUTTING FORCES; DYNAMIC FRICTION; THERMOVISCOPLASTIC BEHAVIOR; TOOL HEATING;

CUTTING TOOLS;

EID: 8344261315     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijmachtools.2004.07.004     Document Type: Article

References (24)

1. N. Narutaki, Y. Yamane, K. Hayashi, T. Kitagawa, High speed machining of Inconel 718 with ceramic tools, Ann. CIRP 42 (1993) 103-106.
2. T.I. El-Wardany, E. Mohammed, M.A. Elbestawi, Cutting temperature of ceramic tools in high speed machining of difficult-to-cut materials, Int. J. Mach. Tools Manufact. 36 (5) (1996) 611-634.
3. M. Rahman, W.K.H. Seah, T.T. Teo, The machinability of Inconel 718, J. Mater. Process. Technol. 63 (1997) 199-204.
4. L.V. Colwell, Predicting the angle of chip flow for single-point cutting tools, Trans. ASME 76 (1954) 199-204.
5. R.S. Hu, P. Mathew, P.L.B. Oxley, H.T. Young, Allowing for end cutting edge effects in predicting forces in bar turning with oblique machining conditions, Proc. Inst. Mech. Engrs 200 (C2) (1986) 89-99.
6. H.T. Young, P. Mathew, P.L.B. Oxley, Allowing for nose radius effects in predicting the chip flow direction and cutting forces in bar turning, Proc. Inst. Mech. Engrs 201 (C3) (1987) 213-226.
7. H.T. Young, P. Mathew, P.L.B. Oxley, Predicting cutting forces in face milling, Int. J. Mach. Tools Manufact. 34 (6) (1994) 771-783.
8. J. Wang, P. Mathew, Development of a general tool model for turning operations based on a variable flow stress theory, Int. J. Mach. Tools Manufact. 35 (1995) 71-90.
9. J.A. Arsecularatne, P. Mathew, P.L.B. Oxley, Prediction of chip flow direction and cutting forces in oblique machining with nose radius tools, Proc. Inst. Mech. Engrs. 209 (1995) 305-315.
10. J.A. Arsecularatne, R.F. Fowle, P. Mathew, Nose radius oblique tool: cutting force and built-up edge prediction, Int. J. Mach. Tools Manufact. 36 (1996) 585-595.
11. J.A. Arsecularatne, R.F. Fowle, P. Mathew, Prediction of chip flow direction, cutting forces and surface roughness in finish turning, J Manufact Sci Eng 120 (1998) 1-12.
12. J. Wang, Development of a chip flow model for turning operations, Int. J. Mach. Tools Manufact. 41 (2001) 1265-1274.
13. G.V. Stabler, The fundamental geometry of cutting tools, Proc. Inst. Mech. Engrs 165 (1951) 14-21.
14. P.L.B. Oxley, Mechanics of Machining, Ellis Horwood, Chichester, UK, 1989.
15. G. Parakkal, R. Zhu, S.G. Kappor, R.E. DeVor, Modeling of turning process cutting forces for grooved tools, Int. J. Mach. Tools Manufact. 42 (2002) 179-191.
16. A. Moufki, D. Dudzinski, A. Molinari, M. Rausch, Thermoviscoplastic modelling of oblique cutting: forces and chip flow predictions, Int. J. Mech. Sci. 42 (2000) 1205-1232.
17. A. Moufki, A. Devillez, D. Dudzinski, A. Molinari, Thermomechanical modelling of oblique cutting and experimental validation, Int. J. Mach. Tools Manufact. 44 (9) (2004) 971-989.
18. A. Molinari, D. Dudzinski, Stationary shear band in high-speed machining, C.R. Acad. Sci. Paris 315 (II) (1992) 399-405.
19. D. Dudzinski, A. Molinari, A modelling of cutting for viscoplastic materials, Int. J. Mech. Sci. 39 (4) (1997) 369-389.
20. A. Moufki, A. Molinari, D. Dudzinski, Modelling of orthogonal cutting with a temperature dependent friction law, J. Mech. Phys. Solids 46 (10) (1998) 2103-2138.
21. E. Usui, H. Takeyama, A photoelastic analysis of machining stresses, J. Eng. Ind. 82 (1960) 303-308.
22. N.N. Zorev, Interrelationship Between Shear Processes Occurring Along Tool Face and on Shear Plane in Metal Cutting, International Research in Production Engineering, ASME, New York, 1963, pp. 42-49.
23. S. Kato, K. Yamaguchi, M. Yamada, Stress distribution at the interface between tool and chip in machining, J. Eng. Ind. 94 (1972) 683-688.
24. D. Buryta, R. Sowerby, I. Yellowley, Stress distributions on the rake face during orthogonal machining, Int. J. Mach. Tools Manufact. 34 (1994) 721-739.