Devulcanization of waste tires using a twin-screw extruder: The effects of processing conditions

Journal of Vinyl and Additive Technology

Volumn 17, Issue 1, 2011, Pages 64-69

  Yazdani, Hamid ^a   Karrabi, Mohammad ^a   Ghasmi, Ismaeil ^a   Azizi, Hamed ^a   Bakhshandeh, Gholam Reza ^a  

^a IRAN POLYMER AND PETROCHEMICAL INSTITUTE   (Iran)

Author keywords

[No Author keywords available]

Indexed keywords

BARREL TEMPERATURE; COMPRESSION SET; CURING AGENTS; CURING BEHAVIOR; DEVULCANIZATES; DEVULCANIZATION; ELONGATION AT BREAK; ENVIRONMENTAL REASONS; PROCESSING CONDITION; RHEOMETRY; RUBBER COMPOUNDS; SCREW SPEED; SOL FRACTION; TWIN SCREW EXTRUDERS; WASTE TIRES;

CURING; EXTRUDERS; MECHANICAL PROPERTIES; RUBBER; SOLS; TENSILE STRENGTH; TIRES;

SCREWS;

EID: 79951745865     PISSN: 10835601     EISSN: 15480585     Source Type: Journal    
DOI: 10.1002/vnl.20257     Document Type: Article

References (21)

1. S. Taghvaie, Rubber Industries Engineering and Research Company Report, 2007.
2. European Tire Recycling Association (ETRA) in 2004.
3. F. Samadian, Industries and Minerals Ministry of IRAN Report, 2007.
4. P. Sutanto, F. Picchioni, and, L.P.B.M. Janssen, J. Appl. Polym. Sci., 102, 5028 (2006).
5. V.Y. Levin, S.H. Kim, A.I. Isayev, J. Massey, and, E. Vonmeerwall, Rubber Chem. Technol., 69, 104 (1996).
6. J. Yun, and, A.I. Isayev, Polym. Eng. Sci., 43, 809 (2003).
7. J. Yun, V. Yashin, and, A.I. Isayev, J. Appl. Polym. Sci., 91, 1646 (2004).
8. M. Mouri, H. Okamoto, M. Matsushita, H. Honda, K. Nakashima, K. Takeushi, Y. Suzuki, and, M. Owaki, Polym. Recycl, 5, 31 (2000).
9. P. Sutanto, F. Picchioni, and, L.P.B.M. Janssen, Chem. Eng. Sci., 61, 7077 (2006).
10. A.R. Jalilvand, I. Ghasemi, M. Karrabi, and, H. Azizi, Plastic Recycl. Technol., 24, 33 (2008).
11. A.R. Jalilvand, I. Ghasemi, M. Karrabi, and, H. Azizi, Iran. Polym. J., 16, 327 (2007).
12. A.R. Jalilvand, I. Ghasemi, M. Karrabi, and, H. Azizi, Iran. Polym. J., 16, 637 (2007).
13. P.J. Flory, and, J. Rehner, J. Chem. Phys., 11, 512 (1943).
14. F.P. Baldwin, and, G. Verstrate, Rubber Chem. Technol., 45, 709 (1972).
15. C. Kumnuantip, and, N. Sombatsompop, Mater. Lett., 57, 3167 (2003).
16. D.A. Baeta, J.A. Zattera, and, P.J. Oliveira, J. Chem. Eng. 26, 23 (2009).
17. M. Mouri, H. Okamoto, M. Matsushita, H. Honda, K. Nakashima, K. Takeushi, Y. Suzuki, and, M. Owaki, Polym. Recycl., 5, 37 (2000).
18. P. Sutanto, F. Picchioni, and, L.P.B.M. Janssen, J. Appl. Polym. Sci., 102, 5028 (2006).
19. M.A.L. Verbruggen, L. Van Der Does, J.W.M. Noordermeer, M. Van Duin, and, H.J. Manuel, Rubber Chem. Technol., 72, 731 (1999).
20. K. Ukumori, and, M. Matsushita, Tech. J. R&D Rev. Toyota, 38, 39 (2003).
21. M.M. Horikx, J. Polym. Sci., 19, 445 (1956).