An environmental friendly recovery production line of waste toner cartridges

Journal of Hazardous Materials

Volumn 185, Issue 2-3, 2011, Pages 696-702

  Ruan, Jujun ^a   Li, Jia ^a   Xu, Zhenming ^a  

^a SHANGHAI JIAO TONG UNIVERSITY   (China)

Author keywords

Environmental friendly recovery production line; Toxicity toner; Waste toner cartridges

Indexed keywords

ENVIRONMENT PROTECTION; ENVIRONMENTAL FRIENDLY RECOVERY PRODUCTION LINE; ENVIRONMENTAL-FRIENDLY; MECHANICAL PRODUCTION; PRODUCTION LINE; RECOVERY PROCESS; RECOVERY RATE; SHEARING PROCESS; TONER CARTRIDGE;

INDUSTRIAL WASTE TREATMENT; MAGNETIC SEPARATION; PROJECTILES; TOXICITY;

RECOVERY;

ALUMINUM; PLASTIC; STEEL;

ALUMINUM; COMPARATIVE STUDY; ENVIRONMENTAL PROTECTION; MAGNETIC METHOD; METAL; PLASTIC; QUANTITATIVE ANALYSIS; SHEAR; STEEL; TOXICITY; WASTE TREATMENT;

ARTICLE; ELECTRONICS; ENVIRONMENTAL HEALTH; ENVIRONMENTAL MANAGEMENT; MAGNETIC SEPARATION; SHEAR STRESS; WASTE TONER CARTRIDGE;

CONSERVATION OF NATURAL RESOURCES; MAGNETICS; REFUSE DISPOSAL;

EID: 78649972823     PISSN: 03043894     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jhazmat.2010.09.074     Document Type: Article

References (20)

1. Cui J., Forssberg E. Mechanical recycling of waste electric and electronic equipment: a review. J. Hazard. Mater. 2003, 99:243-263.
2. Robinson B. E-waste: an assessment of global production and environmental impacts. Sci. Total Environ. 2009, 408:183-191.
3. Li J., Lu H., Guo J., Xu Z., Zhou Y. Recycle technology for recovering resources and products from waste printed circuit boards. Environ. Sci. Technol. 2007, 41:1995-2000.
4. Wu J., Li J., Xu Z. Electrostatic separation for recovering metals and nonmetals from waste printed circuit board: problems and improvements. Environ. Sci. Technol. 2008, 42:5272-5276.
5. Veit H.M., Bernardes A.M., et al. Recovery of copper from printed circuit boards scraps by mechanical processing and electrometallurgy. J. Hazard. Mater. 2006, 137:1704-1709.
6. Li J., Gao S., Duan H., Liu L. Recovery of valuable materials from waste liquid crystal display panel. Waste Manage. 2009, 29:2033-2039.
7. Park Y., Fray D. Recovery of high purity precious metals from printed circuit boards. J. Hazard. Mater. 2009, 164:1152-1158.
8. Waton J., Younas I. Superconducting discs as permanent magnets for magnetic separation. Mater. Sci. Eng B. 1998, 53:220-224.
9. Lungu M., Schlett Z. Vertical drum eddy-current separator with permanent magnets. Int. J. Miner. Process. 2001, 63:207-216.
10. Lungu M. Separation of small nonferrous particles using an angular rotary drum eddy-current separator with permanent magnets. Int. J. Miner. Process. 2005, 78:22-30.
11. Meier-Staude R., Schlett Z., Lungu M. A new possibility in eddy-current separation. Miner. Eng. 2002, 15:287-291.
12. Rem P., Leest P.A., van den Akker A model for eddy current separation. Int. J. Miner. Process. 1997, 49:193-200.
13. Maraspin F., Bevilacqua P., Rem P. Modeling the throw of metals and nonmetals in eddy current separations. Int. J. Miner. Process. 2004, 73:1-11.
14. Zhang S., Forssberg E., Arvidson B., Moss W. Aluminum recovery from electronic scrap by High-Force eddy-current separator. Resour. Conserv. Recycl. 2002, 37:55-60.
15. Zhang S., Forssberg E. Separation mechanisms and criteria of a rotating eddy-current separator operation. Resour. Conserv. Recycl. 1999, 25:215-232.
16. Zhang S., Rem P. Particle trajectory simulation of two-drum eddy current separators. Resour. Conserv. Recycl. 1999, 26:71-90.
17. Li J., Xu Z., Zhou Y. Application of corona discharge and electrostatic force to separate metals and nonmetals from crushed particles of waste printed circuit boards. J. Electrostat. 2007, 65:233-238.
18. Lu H., Li J., Guo J., Xu Z. Pulverization characteristics and pulverizing of waste printed circuit boards(printed wiring boards) based on resource utilization. J. Shanghai Jiaotong Univ. 2007, 04:551-556. (in Chinese).
19. Yang H. Solid Waste Treatment Technology and Engineering Application 2003, China Machine Press, Beijing, (in Chinese).
20. Augusto P., Castelo-Grande T., Barbosa D., Estóevez A. Influence of the processing variables on the performance of MAGCLATM: Angle of the trunk and speed of rotation. Chem. Eng. Process. 2008, 47:1585-1593.