An evaluation of two methods for producing intermetallic microchannels

ASME International Mechanical Engineering Congress and Exposition, Proceedings

Volumn , Issue , 2002, Pages 261-266

  Paul, Brian K ^a   Hasan, Hadi ^a   Dewey, Tyler ^a   Alman, David ^b   Wilson, Richard D ^b  

^a Oregon State University   (United States)

^b NATIONAL ENERGY TECHNOLOGY LABORATORY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

AUTOMOTIVE FUELS; CERAMIC MATERIALS; ELECTROMECHANICAL DEVICES; ENERGY CONVERSION; FUEL CELLS; INTERMETALLICS; MECHANICAL ENGINEERING; MEMS; PUMPS; REFRACTORY MATERIALS; SHRINKAGE; SINTERING; SYNTHESIS (CHEMICAL);

ALUMINIDE INTERMETALLICS; BINDER REMOVAL; CERAMIC TAPES; CHEMICAL INERTNESS; CHEMICAL SYNTHESIS; CHEMICAL SYSTEMS; DIMENSIONAL INSTABILITY; DURING PHASE; HEAT PUMPS; HIGH TEMPERATURE; HIGH-TEMPERATURE RESISTANCE; HYDROGEN SEPARATION; MATERIAL REQUIREMENTS; MICRO-REACTOR; MICROCHANNEL ARRAY; MICROLAMINATION; MICROTECHNOLOGY; MULTILAYER CERAMICS; PHASE CHANGE; POINT-OF-USE; SINTERING PROCESS; VOLUMETRIC SHRINKAGE; WASTE REMEDIATION;

MICROCHANNELS;

EID: 78249270151     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/IMECE2002-32892     Document Type: Conference Paper

References (20)

1. Little, W. A., "Microminiature Refrigerators for Joule-Thomson Cooling of Electronic Chips and Devices," Advances in Cryogenic Engineering, (Vol. 35,1990), pp. 1325-1333.
2. Benson, R. S. and J.W. Ponton,, "Process Miniaturization- A Route To Total Environmental Acceptability?" Trans. IChemE, (Vol. 71, Part A, 1993), pp.160-168.
3. Koeneman, P. B., I. J. Busch-Vishniac, and K. L. Wood, "Feasibility of Micro Power Supplies for MEMS," J. MicroElectoMechanical Sys, (Vol. 6(4), 1997), pp. 355-362.
4. Peterson, R.B. "Size Limits for Regenerative Heat Engines," Microscale Thermophysical Engineering, (Vol. 2, 1998), pp. 121-131.
5. Peterson, R.B, "Numerical Modeling of Conduction Effects in Microscale Counterflow Heat Exchangers," Microscale Thermophysical Engineering, (Vol.3, 1999), pp. 17-30.
6. Matson, D. W., P. Martin, D. Stewart, A. Tonkovich, M. White, J. Zilka, and G. Roberts, "Fabrication of Microchannel Chemical Reactors Using a Metal Lamination Process," Proc. IMRET3, (April, Frankfurt, Germany, 1999).
7. Hessel V., W. Ehrfeld, K. Golbig, Ch. Hoffmann, H. Lowe, and M. Storz, "High temperature HCN gerneration in a complex integrated micro-reaction system," Proc. IMRET3, (April, Frankfurt, Germany, 1999).
8. Chaumat, G. F. Moret, and A. Gasse, "SiC brazing for ceramic heat exchangers," DVS-Berichte, (v166, 1995), pp-217-219.
9. Kim, M., Yi, M. Zhong, J., Bau, H.H., Hu, H. and Ananthasuresh, S.G.K., "The Fabrication of Flow Conduits in Ceramic Tapes and the Measurement of Fluid Flow through These Conduits," Proceedings of the ASME Dynamic Systems and Controls Division, DSC- (Vol. 66, 1998), 171-177.
10. th edition.
11. Golberg, D., Demura, M. and Hirano, T., "Effects of Al-rich off-stoichiometry on the yield stress of binary Ni3Al single crystals," Acta materialia, 1998, 46: 2695-2703. (Pubitemid 128422706)
12. Alman, D.E. and Dogan, C.P., "Intermetallic Sheets Synthesized from Elemental Ti, Al, and Nb Foils," Metallurgical and Materials Transactions A, (26A, October, 1995), 2759-62.
13. Alman, D.E. "Fabrication, Structure and Properties of Aluminum-Aluminide Layered Composites," Mat. Res. Soc. Proc., 1996, 434: 255-260.
14. 3Al thin foil by cold-rolling" Intermetallics, 9(2001),157-167
15. 3Al," Mechanical Properties of Structural Films, STP 1413, American Society for Testing and Materials, West Conshohocken, PA, 2000.
16. Brandes, E.A and Brook, G.B (Ed.), Smithells metal reference book, 1992, seventh edition.
17. Stoloff, N. S., and Sikka V. K. (editors) (1996), Physical Metallurgy and Processing of Intermetallic Compounds, Chapman and Hall, New York, NY, pp. 217.
18. ASM Metal Handbook, Volume 2, Properties and Selection: Nonferrous Alloys and Special Purpose Materials (1990), American Society for Metals, Metals Park, Ohio, pp. 914-920.
19. Paul, B.K., H. Hasan, J. Thomas, R. Wilson, and D. Alman, "Limits on Aspect Ratio in Two-fluid Micro-scale Heat Exchangers," Transactions of NAMRC XXIX, Gainesville, FL, 2001.
20. Thomas, J. and B.K. Paul, "Thermally-Enhanced Edge Registration (TEER) for Aligning Metallic Microlaminated Devices," Transactions of NAMRC XXX, West Lafayette, IN, May 21-24, 2002.