Sliding distance, contact pressure and wear in sheet metal stamping

Wear

Volumn 268, Issue 11-12, 2010, Pages 1275-1284

  Pereira, Michael P ^a   Yan, Wenyi ^b   Rolfe, Bernard F ^a  

^a DEAKIN UNIVERSITY   (Australia)

^b MONASH UNIVERSITY   (Australia)

Author keywords

Contact pressure; Finite element analysis; Sheet metal stamping; Sliding distance; Wear

Indexed keywords

CONTACT CONDITIONS; CONTACT PRESSURES; DIE RADIUS; FINITE ELEMENT ANALYSIS; GENERAL APPROACH; NUMERICAL SIMULATION; SLIDING CONTACTS; SLIDING DISTANCES; TIME-DEPENDENT; TRANSIENT STAGE;

COMPUTER SIMULATION; DIES; FINITE ELEMENT METHOD; METAL STAMPING; METALS; PAPER SHEETING;

SHEET METAL;

EID: 77951107324     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2010.01.020     Document Type: Article

References (29)

1. Gåård A., Krakhmalev P., Bergström J., and Hallbäck N. Galling resistance and wear mechanisms-cold work tool materials sliding against carbon steel sheets. Tribol. Lett. 26 (2007) 67-72
2. van der Heide E., Stam E.D., Giraud H., Lovato G., Akdut N., Clarysse F., Caenen P., and Heikillä I. Wear of aluminium bronze in sliding contact with lubricated stainless steel sheet material. Wear 261 (2006) 68-73
3. Alinger M.J., and Van Tyne C.J. Evolution of die surfaces during repeated stretch-bend sheet steel deformation. J. Mater. Process. Technol. 141 (2003) 411-419
4. Boher C., Attaf D., Penazzi L., and Levaillant C. Wear behaviour on the radius portion of a die in deep-drawing: identification, localisation and evolution of the surface damage. Wear 259 (2005) 1097-1108
5. Ersoy-Nürnberg K., Nürnberg G., Golle M., and Hoffmann H. Simulation of wear on sheet metal forming tools-an energy approach. Wear 265 (2008) 1801-1807
6. Hoffmann H., Nürnberg G., Ersoy-Nürnberg K., and Herrmann G. A new approach to determine the wear coefficient for wear prediction of sheet metal forming tools. Prod. Eng. 1 (2007) 357-363
7. Liljengren M., Kjellsson K., and Wiklund D. Guidelines for die materials, hardening methods and surface coatings for forming of high, extra high and ultra high strength steel sheets (HSS/EHSS/UHSS). Proc. IDDRG 2008 Conference. Olofström, Sweden (2008) 603-614
8. Sandberg O., Bustad P.-A., Carlsson B., Fällström M., and Johansson T. Characterisation of tool wear in stamping of EHS and UHS steel sheets. Proc. International Conference on Recent Advances in Manufacture & Use of Tools & Dies and Stamping of Steel Sheets. Olofström, Sweden (2004) 151-170
9. Rhee S.K. Wear equation for polymers sliding against metal surfaces. Wear 16 (1970) 431-445
10. Bayer R.G. A general model for sliding wear in electrical contacts. Wear 162-164 (1993) 913-918
11. Archard J.F. Contact and rubbing of flat surfaces. J. Appl. Phys. 24 (1953) 981-988
12. Hsu S.M., Shen M.C., and Ruff A.W. Wear prediction for metals. Tribol. Int. 30 (1997) 377-383
13. Attaf D., Penazzi L., Boher C., and Levaillant C. Mechanical study of a sheet metal forming dies wear. Proc. 6th International Tooling Conference. Karlstad, Sweden (2002) 209-221
14. Coubrough G.J., Alinger M.J., and Van Tyne C.J. Angle of contact between sheet and die during stretch-bend deformation as determined on the bending-under-tension friction test system. J. Mater. Process. Technol. 130-131 (2002) 69-75
15. Eriksen M. The influence of die geometry on tool wear in deep drawing. Wear 207 (1997) 10-15
16. Hanaki K., and Kato K. Pressure peak in bending and unbending process. Adv. Technol. Plastic. 1 (1984) 581-586
17. Hortig D., and Schmoeckel D. Analysis of local loads on the draw die profile with regard to wear using the FEM and experimental investigations. J. Mater. Process. Technol. 115 (2001) 153-158
18. Kim Y.S., Jain M.K., and Metzger D.R. Non-uniform pressure distribution in draw-bend friction test and its influence on friction measurement. Proc. NUMISHEET 2005 Conference. Detroit, MI (USA) (2005) 661-666
19. Jensen M.R., Damborg F.F., Nielsen K.B., and Danckert J. Applying the finite-element method for determination of tool wear in conventional deep-drawing. J. Mater. Process. Technol. 83 (1998) 98-105
20. Mortensen J., Dirks J., and Christensen P. A combined physical and numerical simulation of tool performance in conventional deep-drawing operations. Proc. IDDRG 18th Biennial Congress. Lisbon, Portugal (1994) 233-240
21. Pereira M.P., Duncan J.L., Yan W., and Rolfe B.F. Contact pressure evolution at the die radius in sheet metal stamping. J. Mater. Process. Technol. 209 (2009) 3532-3541
22. Pereira M.P., Yan W., and Rolfe B.F. Contact pressure evolution and its relation to wear in sheet metal forming. Wear 265 (2008) 1687-1699
23. Dassault Systèmes Simulia Corp. Abaqus Version 6. 8 Documentation (2008), Dassault Systèmes, Providence, RI, USA
24. Bayer R.G. Engineering Design for Wear. 2nd ed. (2004), Marcel Dekker, New York
25. Yan W., Busso E.P., and O'Dowd N.P. A micromechanics investigation of sliding wear in coated components. Proc. R. Soc. Lond. A 456 (2000) 2387-2407
26. de Rooij M.B., and Schipper D.J. Analysis of material transfer from a soft workpiece to a hard tool: Part I-Lump Growth Model. J. Tribol. 123 (2001) 469-473
27. Schedin E., and Lehtinen B. Galling mechanisms in lubricated systems: a study of sheet metal forming. Wear 170 (1993) 119-130
28. Marciniak Z., Duncan J.L., and Hu S.J. Mechanics of Sheet Metal Forming. second ed. (2002), Butterworth-Heinemann, Oxford
29. Liljengren M., Kjellsson K., Johansson T., and Asnafi N. Die materials, hardening methods and surface coatings for forming of high extra high and ultra high strength steel sheets (HSS/EHSS/UHSS). Proc. IDDRG 2006 Conference. Porto, Portugal (2006) 597-604