Contact pressure evolution at the die radius in sheet metal stamping

Journal of Materials Processing Technology

Volumn 209, Issue 7, 2009, Pages 3532-3541

  Pereira, Michael P ^a   Duncan, John L ^b   Yan, Wenyi ^c   Rolfe, Bernard F ^a  

^a DEAKIN UNIVERSITY   (Australia)

^b UNIVERSITY OF AUCKLAND   (New Zealand)

^c MONASH UNIVERSITY   (Australia)

Author keywords

Bending under tension; Contact pressure; Sheet metal stamping; Tool wear

Indexed keywords

DIES; KNOWLEDGE BASED SYSTEMS; METAL STAMPING; METALS; PHASE INTERFACES;

BENDING-UNDER-TENSION; BLANK MATERIALS; CHANNEL FORMING PROCESS; CONTACT AREAS; CONTACT CONDITIONS; CONTACT PHENOMENON; CONTACT PRESSURE; DEFORMATION CONDITIONS; DIE RADIUS; INFORMATION CONCERNING; INTERMEDIATE STAGES; SHEET METAL FORMING; SHEET METAL STAMPING; TOOL LIVES; TOOL WEAR; WEAR MODELS; WEAR RESISTANT MATERIALS; WEAR RESPONSE; WEAR TESTS;

SHEET METAL;

EID: 62949188952     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2008.08.010     Document Type: Article

References (18)

1. Attaf D., Penazzi L., Boher C., and Levaillant C. Mechanical study of a sheet metal forming dies wear. In: Bergström J., Fredriksson M., Johansson M., Kotik O., and Thuvander F. (Eds). Proceedings of 6th International Tooling Conference. Karlstad, Sweden (2002) 209-221
2. Boher C., Attaf D., Penazzi L., and Levaillant C. Wear behaviour on the radius portion of a die in deep-drawing: identification, localisation and evolution of the surface damage. Wear 259 (2005) 1097-1108
3. Christiansen S., and De Chiffre L. Topographic characterization of progressive wear on deep drawing dies. Tribol. Trans. 40 (1997) 346-352
4. Coubrough G.J., Alinger M.J., and Van Tyne C.J. Angle of contact between sheet and die during stretch-bend deformation as determined on the bending-under-tension friction test system. J. Mater. Process. Technol. 130-131 (2002) 69-75
5. Eriksen M. The influence of die geometry on tool wear in deep drawing. Wear 207 (1997) 10-15
6. Groche P., and Nitzsche G. Reduction of friction in deep drawing of aluminium alloys by generating local hydrostatic-pressure lubrication. Proc. Inst. Mech. Eng. B 220 (2006) 43-48
7. Hanaki K., and Kato K. Pressure peak in bending and unbending process. Adv. Technol. Plast. 1 (1984) 581-586
8. Hortig D., and Schmoeckel D. Analysis of local loads on the draw die profile with regard to wear using the FEM and experimental investigations. J. Mater. Process. Technol. 115 (2001) 153-158
9. Jensen M.R., Damborg F.F., Nielsen K.B., and Danckert J. Applying the finite-element method for determination of tool wear in conventional deep-drawing. J. Mater. Process. Technol. 83 (1998) 98-105
10. Karima M. Practical application of process simulation in stamping. J. Mater. Process. Technol. 46 (1994) 309-320
11. Marciniak Z., Duncan J.L., and Hu S.J. Mechanics of Sheet Metal Forming. 2nd edition (2002), Butterworth-Heinemann, Oxford
12. Mortensen J., Dirks J., and Christensen P. A combined physical and numerical simulation of tool performance in conventional deep-drawing operations. Proceedings of IDDRG 18th Biennial Congress. Lisbon, Portugal (1994) 233-240
13. Pereira M., Yan W., and Rolfe B.F. Modeling of contact pressure in sheet metal forming. Mater. Sci. Forum 561-565 (2007) 1975-1978
14. Pereira, M.P., Yan, W., Rolfe, B.F., 2008. Contact pressure evolution and its relation to wear in sheet metal forming. Wear. doi:10.1016/j.wear.2008.04.042.
15. Ranta-Eskola A., Kumpulainen J., and Sulonen M. Comparison of strip drawing tests used for measuring surface interactions in press forming. In: Ligure S.M. (Ed). Proceedings of IDDRG 12th Biennial Congress. Italy (1982) 165-174
16. Rhee S.K. Wear equation for polymers sliding against metal surfaces. Wear 16 (1970) 431-445
17. Sandberg O., Bustad P.-A., Carlsson B., Fällström M., and Johansson T. Characterisation of tool wear in stamping of EHS and UHS steel sheets. Proceedings of Recent Advances in Manufacture & Use of Tools & Dies and Stamping of Steel Sheets. Olofström, Sweden (2004) 127-146
18. Swift H.W. Plastic bending under tension. Engineering 166 (1948) 333-359