Determination of the temperature rise within UHMWPE tibial components during tribological loading

Acta Biomaterialia

Volumn 6, Issue 2, 2010, Pages 552-562

  Galetz, Mathias C ^a   Uth, Tobias ^b   Wimmer, Markus A ^b   Adam, Peter ^c   Glatzel, Uwe ^a  

^a UNIVERSITY OF BAYREUTH   (Germany)

^b RUSH UNIVERSITY MEDICAL CENTER   (United States)

^c FRIEDRICH SCHILLER UNIVERSITY JENA   (Germany)

Author keywords

Artificial joints; Contact temperature; Frictional heating; Knee replacement; UHMWPE

Indexed keywords

CHROMIUM ALLOYS; COBALT ALLOYS; FRICTION; HIP PROSTHESES; JOINTS (ANATOMY); KNEE PROSTHESES; LUBRICANTS; NONMETALLIC MATRIX COMPOSITES; TERNARY ALLOYS; THERMOCOUPLES; TRIBOLOGY;

ARTIFICIAL JOINT; COEFFICIENT OF FRICTIONS; CONTACT TEMPERATURE; FRICTIONAL HEATING; IN-VIVO MEASUREMENT; KNEE IMPLANTS; TEMPERATURE INCREASE; TEMPERATURE RISE; TIBIAL COMPONENT; ULTRA-HIGH MOLECULAR WEIGHT POLYETHYLENES (UHMWPE);

ULTRAHIGH MOLECULAR WEIGHT POLYETHYLENES;

LUBRICATING AGENT; ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE;

AMBIENT AIR; ARTICLE; CALCULATION; CHEMICAL ANALYSIS; CHEMICAL REACTION KINETICS; CONTROLLED STUDY; EQUIPMENT DESIGN; FLOW RATE; FRICTION; HEAT STRESS; KNEE PROSTHESIS; LABORATORY TEST; LUBRICATION; MECHANICAL STRESS; PHYSICAL CHEMISTRY; PRIORITY JOURNAL; TEMPERATURE DEPENDENCE; TEMPERATURE MEASUREMENT; THEORETICAL MODEL; TIBIA;

CALLUNA VULGARIS;

EID: 72049092674     PISSN: 17427061     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.actbio.2009.06.023     Document Type: Article

References (42)

1. Pritchett J.W. Heat generated by knee prostheses. Clin Orthop Relat Res 442 (2005) 195-198
2. Bergmann G., Graichen F., Rohlmann A., Verdonschot N., and van Lenthe G.H. Frictional heating of total hip implants. Part 1: measurements in patients. J Biomech 34 (2001) 421-428
3. Davidson J.A., and Schwartz G. Wear, creep, and frictional heat of femoral implant articulating surfaces and the effect on long-term performance-part 1, review. J Biomed Mat Res 21 (1987) 261-285
4. Liao Y.S., McKellop H., Lu Z., Campbell P., and Benya P. The effect of frictional heating and forced cooling on the serum lubricant and wear of UHMW polyethylene cups against cobalt-chromium and zirconia balls. Biomaterials 24 (2003) 3047-3059
5. Uetz H., and Wiedemeyer J. Tribologie der Polymere (1985), Hanser
6. Achenbach M, Frank E. Reibung von Elastomeren. Tribologie + Schmierungstechnik 2001;48:43-7.
7. Greenwood J.A., Minchall H., and Tabor D. Hysteresis losses in rolling and sliding friction. Proc Royal Soc A259 (1960) 480-507
8. Briscoe B.J. Friction and wear of organic solids and the adhesion model of friction. Phil Magazine A43 (1981) 511-527
9. Galetz M.C., Goetz C., Adam P., and Glatzel U. Hysteretic heating during cyclic loading of ultra high molecular weight polyethylene. Adv Eng Mat 9 (2007) 1089-1096
10. Deng M., Latour R.A., Ogale A.A., and Shalaby S.W. Study of creep behavior of ultra-high-molecular-weight polyethylene systems. J Biomed Mat Res Part A 40 (1997) 214-223
11. Miura H. Prediction of total knee arthroplasty polyethylene wear using the wear index. J Arthroplasty 17 (2002) 760-766
12. Lewis R.B. Predicting the wear of sliding plastic surfaces. Mech Eng 86 (1964) 32-40
13. Petty W., Miller G.J., Bartel D.L., Wright T.M., and Burstein A.H. Total knee contact pressures: the effect of congruity and alignment medscape. General Med 1 (1999) 1-5
14. Sathasivam S., and Walker P.S. The conflicting requirements of laxity and conformity in total knee replacement. J Biomech 32 (1999) 239-247
15. Sawyer W.G., Hamilton M.A., Fregly B.J., and Banks S.A. Temperature modeling in a total knee joint replacement using patient-specific kinematics. Tribol Lett 15 (2003) 343-351
16. Carslaw H.S., and Jaeger J.C. Conduction of heat in solids (1959), Clarendon, Oxford
17. Samyn P., and Schoukens G. Calculation and significance of the maximum polymer surface temperature T* in reciprocating cylinder-on-plate sliding. Polym Eng Sci 48 (2008) 774-785
18. Blok H. Theoretical study of temperature rise at surfaces of actual contact under oiliness lubricating conditions. Proc General Discussion on Lubrication Inst. Mech. Engs 2 (1937) 222-235
19. Bhushan B. Modern tribology handbook: vol. 1 - principles of tribology (2001), CRC Press
20. Imado K., Miura A., Nagatoshi M., Kido Y., Miyagawa H., and Higaki H. A study of contact temperature due to frictional heating of UHMWPE. Tribol Lett 16 (2004) 265-273
21. Schwenke T., Borgstede L.L., Schneider E., Andriacchi T.P., and Wimmer M.A. The influence of slip velocity on wear of total knee arthroplasty. Wear 259 (2005) 926-932
22. Rittel D. Transient temperature measurement using embedded thermocouples. Exp Mech H38 (1998) 73-79
23. Ngai V., Schwenke T., Andriacchi T.P., and Wimmer M.A. Kinematics of total knee replacement (TKR) patients versus knee simulator input data. J Biomech 128 (2006)
24. Ashby M.F., and Kong H. Friction - heating maps and their application. Mat Res Soc Bull 16 (1991) 41-47
25. Kragelski I., Dobycin N., and Kombalov V. Grundlagen der Berechnung von Reibung und Verschleiß (1983), Hanser
26. Unal H., and Mimaroglu A. Friction and wear behaviour of unfilled engineering thermoplastics. Mat Design 24 (2003) 183-187
27. Thumb N., Bröll H., and Czurda R. Praktische rheumatologie (2001), Springer
28. Blake A.S.T., Petley G.W., and Deakin C.D. Effects of changes in packed cell volume on the specific heat capacity of blood: implications for studies measuring heat exchange in extracorporeal circuits. BJA Brit J Anaesthesia 84 (2000) 28-32
29. Liao Y.S., Benya P.D., and McKellop H.A. Effect of protein lubrication on the wear properties of materials for prosthetic joints. Appl Biomat 48 (1999) 465-473
30. Lu Z., and McKellop H. Frictional heating of bearing materials tested in a hip joint wear simulator. Proc Inst Mech Eng H J Eng Med 211 (1997) 101-108
31. Zichner L.P., and Willert H.G. Comparison of alumina-polyethylene and metal-polyethylene in clinical trials. Clin Orthop Relat Res 282 (1992) 86-94
32. Urban J.A., Garvin K.L., Boese C.K., Bryson L., Pedersen D.R., Callaghan J.J., et al. Ceramic-on-polyethylene bearing surfaces in total hip arthroplasty. Seventeen to twenty-one-year results. J Bone Joint Surg Am 82 (2001) 1688-1694
33. Tanaka K., and Miyata T. Study on the friction and transfer of semicrystalline polymers. Wear 41 (1977) 383
34. Furukama J. Physical chemistry of polymer rheology (2003), Springer, Heidelberg
35. Wieleba A. The mechanism of tribological wear of thermoplastic materials. Arch Civil Mech Eng 4 (2007) 185-191
36. Young T.H., Cheng C.K., Lee Y.M., Chen L.Y., and Haung C.H. Analysis of ultrahigh molecular weight polyethylene failure in artificial knee joints: thermal effect on long-term performance. J Biomed Mat Res 48 (1998) 159-164
37. Wimmer M.A., et al. A striated pattern of wear in ultrahigh-molecular-weight polyethylene components of Miller-Galante total knee arthroplasty. J Arthroplasty 13 (1998) 8-16
38. Chandrasekaran M., Wei L.Y., Venkateshwaran K.K., Batchelor A.W., and Loh N.L. Tribology of UHMWPE tested against a stainless steel counterface in unidirectional sliding in presence of model synovial fluids: Part 1. Wear 223 (1998) 13-21
39. Williams M.L., Landel R.F., and Ferry J.D. The temperature dependence of relaxation mechanisms in amorphous polymers and other glass-forming liquids. J Am Chem Soc 77 (1955) 3701-3707
40. Kurtz S.M., Villaraga M.L., Herr M.P., Bergström J.S., Rimnac C.M., and Edidin A.A. Thermomechanical behaviour of virgin and highly crosslinked ultra-high molecular weight polyethylene used in total joint replacements. Biomaterials 23 (2002) 3681-3697
41. Walker P.S., Blunn G.W., and Lilley P.A. Wear testing of materials and surfaces for total knee replacement. J Biomed Mat Res 33 (1996) 159-175
42. Wang A., Essner A., and Klein R. Effect of contact stress on friction and wear of ultra-high molecular weight polyethylene in total hip replacement. Proc Inst Mech Eng H J Eng Med 205 (2001) 133-139