Effect of glass bead content and diameter on shrinkage and warpage of injection-molded PA6

Polymer Engineering and Science

Volumn 49, Issue 11, 2009, Pages 2218-2224

  Kovacs J G ^a   Solymossy, B ^a  

^a BUDAPEST UNIVERSITY OF TECHNOLOGY AND ECONOMICS   (Hungary)

Author keywords

[No Author keywords available]

Indexed keywords

DEFORMATION; GLASS; GRANULAR MATERIALS; INJECTION MOLDING;

% REDUCTIONS; GLASS BEAD; INJECTION MOLDED PRODUCTS; INJECTION MOULDED; POLYAMIDE 6; PROPERTY; SHRINKAGE VALUE; SIMPLE++; SPECIFIC LOCATION; WARPAGES;

SHRINKAGE;

EID: 70350220537     PISSN: 00323888     EISSN: 15482634     Source Type: Journal    
DOI: 10.1002/pen.21470     Document Type: Article

References (28)

1. K.M.B. Jansen, D.J.V. Dijk, and M.H. Husselman, Polym. Eng. Sci., 38, 838 (1998).
2. K.M.B. Jansen, G. Titomanilo, and R. Pantani, Int. Polym. Proc., 12, 4 (1997).
3. P. Postawa and J. Koszkul, J. Mater. Process. Tech., 162, 109 (2005).
4. B.H. Min, J. Mater. Process. Tech., 136, 1 (2003).
5. A. Mamat, T.F. Trochu, and B. Sanschagrin, Polym. Eng. Sci., 35, 1511 (1995).
6. K. Shelesh-Nezhad and A. Taghizadeh, Polym. Eng. Sci., 47, 2124 (2007).
7. S.J. Liao, D.Y. Chang, H.J. Chen, L.S. Tsou, J.R. Ho, H.T. Yau, W.H. Hsieh, J.T. Wang, and Y.C. Su, Polym. Eng. Sci., 44, 917 (2004).
8. J.G. Kovács, Ph.D. Thesis, Design and Simulation of Injection Molded Products, Budapest University of Technology and Economics (BME), Budapest (2007).
9. R.A. Malloy, Plastic Part Design for Injection Molding, Carl Hanser Verlag, Münich (1994).
10. J.M. Fischer, Handbook of Molded Part Shrinkage and Warpage, Plastics Design Library, Norwich (2003).
11. R. Thomas and N. Mccaffery, SPE ANTEC., 89, 371 (1989).
12. R.M. Shay, P.H. Foss, and C.C. Mentzer, SPE RETEC., 1, 496 (1996).
13. W.S. Depolo and D.G. Baird, Polym. Compos., 27, 239 (2006).
14. J.-Z. Liang and R.K.Y. Li, J. Appl. Polym. Sci., 73, 1451 (1999).
15. J.-Z. Liang, R.K.Y. Li, and S.C. Tjong, Polym. Test., 19, 213 (2000).
16. J.-Z. Liang, Macromol. Mater. Eng., 286, 714 (2001).
17. J.-Z. Liang, Macromol. Mater. Eng., 287, 588 (2002).
18. C.K. Huang, S.W. Chen, and C.T. Yang, Polym. Eng. Sci., 45, 1471 (2005).
19. S. Hashemi, Express Polym. Lett., 2, 474 (2008).
20. R.K.Y. Li, J.-Z. Liang, and S.C. Tjong, J. Mater. Process Tech., 79, 59 (1998).
21. J.-Z. Liang, R.K.Y. Li, and S.C. Tjong, Polym. Test., 16, 529 (1998).
22. H. Unal, Mater. Des., 25, 483 (2004).
23. S.O. Ogadhoh and T.D. Papathanasiou, Compos. Part AAppl. S., 27, 57 (1996).
24. J.-Z. Liang and R.K.Y. Li, J. Reinf. Plast. Comp., 20, 630 (2001).
25. S.C. Jana, Polym. Eng. Sci., 43, 570 (2003).
26. J.G. Kovács and T. Tábi, Proccedings of the Fifth Conference on Mechanical Engineering, Budapest, 5, 5 (2006).
27. E. Lafranche, P. Krawczak, J.-P. Ciolczyk, and J. Maugey, Adv. Polym. Tech., 24, 114 (2005).
28. E. Lafranche, P. Krawczak, J.-P. Ciolczyk, and J. Maugey, Express Polym. Lett., 1, 456 (2007).