Effect of processing conditions on shrinkage in injection molding

Polymer Engineering and Science

Volumn 38, Issue 5, 1998, Pages 838-846

  Jansen, K M B ^a   Van Dijk, D J ^a   Husselman, M H ^a  

^a UNIVERSITY OF TWENTE   (Netherlands)

Author keywords

[No Author keywords available]

Indexed keywords

AMORPHOUS MATERIALS; PLASTIC MOLDS; PRESSURE EFFECTS; SHRINKAGE; THERMOPLASTICS;

AMORPHOUS POLYMERS;

INJECTION MOLDING;

EID: 0032058033     PISSN: 00323888     EISSN: None     Source Type: Journal    
DOI: 10.1002/pen.10249     Document Type: Article

References (39)

1. K. M. B. Jansen, G. Titomanlio and R. Pantani, "In-Mold Shrinkage Measurements of PS Samples With Strain Gauges," Intern. Polym. Proc., XII, 4 (1997).
2. D. Rosato and D. Rosato, Injection Molding Handbook, 2nd ed., p. 484, Chapman and Hall, London (1995).
3. A. Mamat et al, Polym. Eng., Sci., 35, 1511 (1995).
4. H. Kumazawa, SPE ANTEC Tech. Papers, 40, 817 (1994).
5. M. F. Bain et al., SPE ANTEC Tech. Papers, 38, 977 (1992).
6. P. Delbarre et al., SPE ANTEC Tech. Papers, 37, 301 (1991).
7. A. I. Isayev and T. Hariharan, Polym. Eng. Sci., 25, 271 (1985).
8. M. R. Nagy, SPE ANTEC Tech. Papers, 39, 2155 (1993).
9. C. Liu and L. T. Manzione, Polym. Eng. Sci., 36, 1 (1996).
10. K. M. B. Jansen, G. Titomanlio, and R. Pantani, Polym. Eng. Sci., 38, 254 (1998).
11. V. Leo and C. H. Cuvelliez, Polym. Eng. Sci., 36, 1961 (1996).
12. C. A. Heiber et al., SPE ANTEC Tech. Papers, 37, 259 (1991).
13. L. P. Herbert et al., SPE ANTEC Tech. Papers, 37, 430 (1991).
14. S. J. Ni and K. K. Wang, SPE ANTEC Tech. Papers, 39, 612 (1993).
15. A. G. Gennari, SPE ANTEC Tech. Papers, 39, 3436 (1993).
16. G. Burke and D. Kazmer, SPE ANTECH Tech. Papers, 38, 1354 (1992).
17. R. M. Shay et al., Proc. RETEC (Nov. 1995).
18. H. Ries, Kunststoffe, 84, 1710 (1994).
19. C. S. Lee and A. Dubin, SPE ANTEC Tech. Papers, 36, 375 (1990).
20. R. Thomas and N. McCaffery SPE ANTEC Tech. Papers, 35, 371 (1989).
21. W. Busko and V. K. Stokes, SPE ANTEC Tech. Papers, 41, 484 (1995).
22. G. Titomanlio and K. M. B. Jansen, Polym. Eng. Sci., 36, 2041 (1996).
23. K. M. B. Jansen, D. J. van Dijk, and M. J. A. Freriksen, "Shrinkage Anisotropy in Fiber reinforced Injection Molded Products," Polym. Compos., in preparation.
24. T. W. Schmidt, PhD thesis, RWTH Aachen, Germany (1987).
25. Annual Book of ASTM Standards, Designation D995-89, Vol. 8.01 (1989).
26. L. C. E. Struik, Internal Stresses, Dimensional Stabilities and Molecular Orientations in Plastics, p. 177, Wiley and Sons, Brisbane (1990).
27. R. Greiner and F. R. Schwarzl, Rheol. Acta, 23, 387 (1984).
28. K. M. B. Jansen and G. Titomanlio, Polym. Eng. Sci., 36, 2029 (1996).
29. W. Busko and V. K. Stokes, Polym. Eng. Sci., 35, 351 (1995).
30. C-Mold 4.0 data.
31. VDMA, Kenndaten fuer die Verarbeitung Thermoplastischer Kunststoffe; Thermodynamik, Hanser Verlag, Munich (1986).
32. P. Zoller and Walsh, Standard Pressure-Volume-Temperature Data for Polymers, Technomic Publishing Company, Lancaster, Pa. (1995).
33. J. Brandrup and E. H. Immergut, Polymer Handbook, Wiley and Sons, New York (1989).
34. E. Moore, ed., Styrene Polymers, Wiley and Sons (1989).
35. H. Domininghaus, Die Kunststoffe und ihre Eigenschaften, VDI Verlag, Düsseldorf, Germany (1992).
36. K. M. B. Jansen, Experim. Mech., (in press).
37. H. W. J. de Vries, Master's thesis (1996).
38. K. M. B. Jansen, Int. J. Heat Mass Transfer, 38, 309 (1995).
39. B. Monasse, J. Mater. Sci., 27, 6047 (1992).