Width modification for gears with low contact ratio

Meccanica

Volumn 44, Issue 5, 2009, Pages 613-621

  İmrek, Hüseyin ^a  

^a SELCUK UNIVERSITY   (Turkey)

Author keywords

Gear; Hertz surface pressure; Tooth modifications; Width modification

Indexed keywords

GEAR TEETH; GEARS; MESH GENERATION;

CONTACT RATIO; SURFACE PRESSURES; TOOTH MODIFICATIONS; WIDTH MODIFICATION;

SPUR GEARS;

EID: 70349748522     PISSN: 00256455     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11012-009-9220-4     Document Type: Article

References (25)

1. N Tsukamoto H Maruyama J Shi 1986 Investigation about prevention of tooth profile change of nylon gears Bull JSME 29 1927 1933
2. C Naruse S Haizuka R Nemoto 1986 Studies on frictional loss, temperature rise and limiting load for scoring of spur gear Bull JSME 29 600 608
3. M Yozhizaki C Naruse R Nemoto S Haizuka 1991 Study on frictional loss of spur gears Tribol Trans 34 138 146
4. K Mao 2006 Gear tooth contact analysis and its application in the reduction of fatigue wear Wear 262 1281 1288 (Pubitemid 46590258)
5. WS Wang ZH Fong 2008 A dual face-hobbing method for the cycloidal crowning of spur gears Mech Mach Theory 43 1416 1430
6. MS Tavakoli DR Houser 1986 Optimum profile modifications for the minimization of static transmission errors of spur gears Trans ASME J Mech Transm Automat Des 108 86 95
7. A Kubo S Kiyono 1980 Vibrational excitation of cylindrical involute gears due to tooth form error Bull JSME 23 183 1536 1543
8. FL Litvin A Fuentes I Gonzalez-Perez L Carnevali K Kawasaki RF Handschuh 2003 Modified involute helical gears: computerized design, simulation of meshing, and stress analysis Comput Methods Appl Mech Eng 192 3619 3655
9. Y Wang HME Cheung WJ Zhang 2001 A finite element approach to dynamic modeling of flexible spatial link-gear systems Mech Mach Theory 36 4 469 487
10. S Li 2007 Effects of machining errors, assembly errors and tooth modifications on loading capacity, load-sharing ratio and transmission error of a pair of spur gears Mech Mach Theory 42 698 726
11. IH Seol DH Kim 1998 The kinematic and dynamic analysis of crowned spur gear drive Comput Methods Appl Mech Eng 167 109 118
12. CH Kim 2006 Durability improvement method for plastic spur gears Tribol Int 39 1454 1461
13. N Tsukamoto K Terashima 1986 Development of plastic gears for power transmission Trans Jpn Soc Mech Eng 29 247 249 255
14. S Senthilvelan R Gnanamoorthy 2006 Effect of gear tooth filet radius on the performance of injection molded Nylon 6/6 gears Mater Des 27 632 639
15. H İmrek H Düzcükoǧlu 2007 Relation between wear and tooth width modification in spur gears Wear 262 390 394
16. H Düzcükoǧlu H İmrek 2008 A new method for preventing premature pitting formation on spur gears Eng Fract Mech 75 4431 4438
17. H İmrek 2009 Performance improvement method for Nylon 6 spur gears Tribol Int 42 503
18. İmrek H, FIrat V, Khalfan OM (2006) Using finite element method to investigate a spur gear whose width is modified. In: International conference on modeling and simulation, Konya, Turkey, 2006, pp 249-253
19. Townsend DP (1992) Dudley's gear handbook. McGraw-Hill, New York
20. Juvinall RC, Marshek KM (1991) Fundamentals of machine components design, 2nd edn. Wiley, New York
21. K Mao 2007 Numerical method for polymer composite gear flash temperature prediction Wear 262 1321 1329
22. O Asi 2006 Fatigue failure of a helical gear in a gearbox Eng Fail Anal 13 1116 1125
23. S Glodez Z Ren J Flasker 1999 Surface fatigue of gear teeth flanks Comput Struct 73 475 483
24. Singh A, Houser DR, Vijayakar S (1996) Early detection of gear pitting. In: ASME Power Transmission and Gearing Conf, DE-vol 88, 1996, pp 673-678
25. İmrek H (1995) Investigation of influences of tooth profiles upon scoring phenomena. PhD thesis, University of Selcuk, Konya, Turkey