Performance improvement method for Nylon 6 spur gears

Tribology International

Volumn 42, Issue 3, 2009, Pages 503-510

  Imrek, Hüseyin ^a  

^a SELCUK UNIVERSITY   (Turkey)

Author keywords

Gear; Load sharing; Nylon gear; Plastic gear; Spur gear; Width modification

Indexed keywords

DENTISTRY; ERROR DETECTION; GEARS; POLYAMIDES; RAYON; SPUR GEARS;

EXPERIMENTAL STUDIES; GEAR PERFORMANCES; HEAT ACCUMULATIONS; LOAD SHARING; NYLON GEAR; NYLON-6; PERFORMANCE IMPROVEMENTS; PLASTIC GEAR; SINGLE TEETH; TOOTH MESHING; TRANSMISSION ERRORS; WEAR RATES; WIDTH MODIFICATION;

GEAR TEETH;

EID: 57649233078     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.triboint.2008.08.011     Document Type: Article

References (21)

1. Crawford R.J. Plastic Engineering. 3rd ed (1998), Butterworth-Heinemann
2. Tsukamoto N. Investigation about the strength of plastic gears (1st report). Trans Jpn Soc Mech Eng 22 173 (1979) 1685-1692
3. Tsukamoto N. Investigation about the strength of plastic gears (2nd report). Trans Jpn Soc Mech Eng 24 191 (1981) 872-881
4. Terashima K., Tsukamoto N., and Nishida N. Development of plastic gears for power transmission. Trans Jpn Soc Mech Eng 29 251 (1986) 1598-1604
5. Terashima K., Tsukamoto N., Nishida T., and Seki K. A study on the power translation plastic gears. Trans Jpn Soc Mech Eng 51 469 (1985) 2309-2315
6. Kurokawa M., Uchiyama Y., Iwai T., and Nagai S. Performance of plastic gear made of carbon fiber reinforced polyamide 12. Wear 254 (2003) 468-473
7. Walton D., Tessema A., Hooke C.J., and Shippen J.M. Load sharing in metallic and non-metallic gear. Proc Inst Mech Eng Part C J Mech Eng Sci 208 (1994) 81-87
8. Mao K. A new approach for polymer composite gear design. Wear 262 (2007) 432-441
9. Mao K., Hooke C.J., and Walton D. Acetal gear wear and performance prediction under unlubricated running condition. J synth Lubr. 23 (2006) 137-152
10. Senthilvelan S., and Gnanamoorthy R. Effect of gear tooth filet radius on the performance of injection molded Nylon 6/6 gears. Mater Des 27 (2006) 632-639
11. Senthilvelan S., and Gnanamoorthy R. Effect of rotational speed on the performance of unreinforced and glass fiber reinforced Nylon 6 spur gears. Mater Des 28 (2007) 765-772
12. Senthilvelan S., and Gnanamoorthy R. Reinforced polymer gear fatigue and failure analysis. Trans Indian Inst Met 58 (2005) 249-253
13. Senthilvelan S., and Gnanamoorthy R. Damage mechanisms in injection molded unreinforced glass and carbon reinforced Nylon 66 spur gears. Appl Compos Mater 11 (2004) 377-397
14. İmrek H., and Düzcükoǧlu H. Relation between wear and tooth width modification in spur gears. Wear 262 (2007) 390-394
15. Düzcükoǧlu H., and İmrek H. A New method for preventing premature formation on spur gears, Engineering Fracture Mechanics 75 (2008) 4431-4438
16. Taburdagitan M., and Akkok M. Determination of surface temperature rise with thermo-elastic analysis of spur gears. Wear 261 (2006) 656-665
17. Terashima K., Tsukamoto N., and Nishida N. Development of plastic gears for power transmission. Trans Jpn Soc Mech Eng 29 250 (1986) 1326-1329
18. Koffi D., Gauvin R., and Yelle H. Heat generation in thermoplastic spur gears. J Mech Trans Autom Des 107 (1985) 31-37
19. Kim C.H. Durability improvement method for plastic spur gears. Tribol Int 39 (2006) 1454-1461
20. Al-Sabti S.L., and Stolarski T.A. Surface fatigue of brittle polymers in rolling line Contact. Tribol Int 31 (1998) 695-699
21. Glodez S., Ren Z., and Flasker J. Surface fatigue of gear teeth fanks. Comput Struct 73 (1999) 475-483