Finite element simulation for burr formation near the exit of orthogonal cutting

International Journal of Advanced Manufacturing Technology

Volumn 43, Issue 9-10, 2009, Pages 1035-1045

  Deng, W J ^a   Xia, W ^a   Tang, Y ^a  

^a SOUTH CHINA UNIVERSITY OF TECHNOLOGY   (China)

Author keywords

Burr formation; Finite element method; Metal cutting

Indexed keywords

BURR FORMATION; CHIP FLOW; CHIP FORMATIONS; COMMERCIAL FINITE ELEMENT CODES; COUPLED THERMO-MECHANICAL; CUTTING CONDITIONS; CUTTING PROCESS; DAMAGE CRITERIA; EXPERIMENTAL DATA; FINITE ELEMENT SIMULATIONS; ORTHOGONAL CUTTING; PLANE-STRAIN; QUANTITATIVE ANALYSIS; SIMULATION PROCEDURES; STEADY STATE; TOOL CONDITION; TOOL EXIT;

COUPLED CIRCUITS; CUTTING TOOLS; FINITE ELEMENT METHOD; PLASTIC DEFORMATION;

METAL CUTTING;

EID: 67651236413     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-008-1784-y     Document Type: Article

References (15)

1. GL Chern 2006 Study on mechanisms of burr formation and edge breakout near the exit of orthogonal cutting J Mater Process Technol 176 152 157
2. WJ Deng W Xia LS Lu Y Tang 2007 Finite element modeling of burr formation in metal cutting with a backup material Adv Mater Res 24-25 71 76
3. Gillespie LK (1973) The formation and properties of machining burrs. M.S. Thesis, Utah State University, Logan, UT
4. LK Gillespie PT Blotter 1976 The formation and properties of machining burrs ASME J Eng Ind 98 66 74
5. YB Guo DA Dornfeld 1998 Finite element analysis of drilling burr minimization with a backup material Trans NAMRI/SME 26 207 211
6. SL Ko JE Chang GE Yang 2003 Burr minimizing scheme in drilling J Mater Process Technol 140 237 242
7. SL Ko DA Dornfeld 1991 Study on burr formation mechanism Trans ASME J, Eng Mater Technol 113 75 87
8. Ko SL, Dornfeld DA (1989) Analysis and modelling of burr formation and breakout in metal. Proceedings, Symposium on Mechanics of Deburring and Surface Finishing Processes at 1989 ASME Winter Annual Meeting (edited by R. J. Stango and P.R. Fitzpatrick), ASME, New York 38:79-92
9. M Luo G Liu M Chen 2008 Mechanism of burr formation in slot milling Al-alloy Int J Mater Prod Technol 31 63 71
10. IW Park DA Dornfeld 2000 A study on burr formation processes using the finite element method-Part I Trans ASME, J Eng Mater Technol 122 221 228
11. IW Park DA Dornfeld 2000 A study of burr formation processes using the finite element method-Part II. The influence of exit angle, rake angle and backup material on burr formation processes Trans ASME, J Eng Mater Technol 122 229 237
12. P Sartkulvanich H Sahlan T Altan 2007 Finite element analysis of burr formation in face milling of a cast Al alloy Min Sci Technol 11 157 181
13. T Shirakashi K Maekawa E Usui 1983 Flow stress of low carbon steel at high temperature and strain rate Bull Jpn Soc Precis Eng 17 167 172
14. A Toropov SL Ko 2006 A model of burr formation in the feed direction in turning Int J Mach Tools Manuf 46 1913 1920
15. GC Wang CY Zhang 2001 Cutting-direction burr formation in orthogonal precision cutting Trans Nanjing Univ Aeronautics Astronautics 18 194 199