Finite element analysis when machining UGF-reinforced PMCs plates: Chip formation, crack propagation and induced-damage

Materials and Design

Volumn 30, Issue 8, 2009, Pages 3295-3302

  Mkaddem, Ali ^a   El Mansori, Mohamed ^a  

^a ARTS ET MÉTIERS PARISTECH   (France)

Author keywords

[No Author keywords available]

Indexed keywords

ADAPTIVE MESHES; CHIP FORMATION MECHANISM; CHIP FORMATIONS; COMPOSITE PLATES; CURRENT MODELS; DYNAMIC EXPLICIT; FAILURE ENVELOPE; FAILURE MECHANISM; FIBRE ORIENTATION; FINITE ELEMENT ANALYSIS; FRP COMPOSITE; HOMOGENEOUS MATERIALS; NUMERICAL MODELS; ORTHOGONAL CUTTING; PLANE-STRESS STATE; PROCESS PARAMETERS; SUB-SURFACE; TSAI-HILL CRITERION;

FUNCTIONALLY GRADED MATERIALS; MACHINING; PLATES (STRUCTURAL COMPONENTS); POLYMER MATRIX COMPOSITES; SIMULATORS;

FINITE ELEMENT METHOD;

EID: 67349153352     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2008.12.009     Document Type: Article

References (27)

1. Koplev A. Cutting of CFRP with single edge tools. In: Third international conference on composite materials: advances in composite materials proceedings, Paris, France; 1980. p. 1597-605.
2. Koplev A., Listrup A., and Vorm T. The cutting process, chips and cutting forces in machining CFRP. Composites 14 4 (1983) 371-376
3. Wang D.H., Ramulu M., and Arula D. Orthogonal cutting mechanisms of graphite/epoxy composite. Part I: Unidirectional laminate. Int J Mac Tools Manuf 35 12 (1995) 1623-1638
4. Wang D.H., Ramulu M., and Arula D. Orthogonal cutting mechanisms of graphite/epoxy composite. Part II: Multi-directional laminate. Int J Mach Tools Manuf 35 12 (1995) 1639-1648
5. Bhatnagar N., Ramakrishnan N., Naik N.K., and Komanduri R. On the machining of fibre reinforced plastic (FRP) composite laminates. Int J Mach Tools Manuf 35 5 (1995) 701-716
6. Arola D., Ramulu M., and Wang D.H. Chip formation in orthogonal trimming of graphite/epoxy composite. Compos A 27 2 (1996) 121-133
7. Palanikumar K., and Davim J.P. Mathematical model to predict tool wear on the machining of glass fibre reinforced plastic composites. Mater Design 28 7 (2007) 2008-2014
8. Iglesias P., Bermudez M.D., Carrion F.J., Chandrasekar S., and Compton W.D. A study of the wear behaviour of polymer-matrix composites containing discontinuous nanocrystalline alloy reinforcements. Tribol Int 40 3 (2007) 479-489
9. Palanikumar K., Karunamoorthy L., and Karthikeyan R. Assessment of factors influencing surface roughness on the machining of glass fibre-reinforced polymer composites. Mater Design 27 10 (2006) 862-871
10. Palanikumar K. Modeling and analysis for surface roughness in machining glass fibre reinforced plastics using response surface methodology. Mater Design 28 10 (2007) 2611-2618
11. Ghidossi P., El Mansori M., and Pierron F. Influence of specimen preparation by machining on the failure of polymer matrix off-axis tensile coupons. Compos Sci Technol 66 11-12 (2006) 1857-1872
12. Seif M.A., Khashaba U.A., and Rojas-Oviedo R. Measuring delamination in carbon/epoxy composites using a shadow moiré laser based imaging technique. Compos Struct 79 1 (2007) 113-118
13. Wang X.M., and Zhang L.C. An experimental investigation into the orthogonal cutting of unidirectional fibre reinforced plastics. Int J Mach Tools Manuf 43 10 (2003) 1015-1022
14. Arola D., and Ramulu M. Orthogonal cutting of fiber-reinforced composites: a finite element analysis. Int J Mech Sci 39 5 (1997) 597-613
15. Arola D., Sultan M.B., and Ramulu M. Finite element modelling of edge trimming fibre-reinforced plastics. Trans ASME, J Manuf Sci Eng 124 1 (2002) 32-41
16. Ramesh M.V., Seetharamu K.N., Ganesan N., and Sivakumar M.S. Analysis of machining of FRPs using FEM. Int J Mach Tools Manuf 38 12 (1998) 1531-1549
17. Mahdi M., and Zhang L. An adaptive three dimensional finite element algorithm for the orthogonal cutting of composite materials. J Mater Process Technol 113 1-3 (2001) 368-372
18. Mahdi M., and Zhang L. A finite element model for the orthogonal cutting of fibre-reinforced composite materials. J Mater Process Technol 113 1-3 (2001) 373-377
19. Bhatnagar N., Nayak D., Singh I., Chouhan H., and Mahajan P. Determination of machining_induced damage characteristics of fibre reinforced plastic composite laminates. Mater Manuf Process 19 6 (2004) 1009-1023
20. Nayak D., Bhatnagar N., and Mahajan P. Machining studies of UD-FRP composites. Part 1: Effect of geometrical and process parameters. Mach Sci Technol 9 4 (2005) 481-501
21. Nayak D., Bhatnagar N., and Mahajan P. Machining studies of UD-FRP composites. Part 2: Finite element analysis. Mach Sci Technol 9 4 (2005) 503-528
22. Venu Gopala Rao G., Mahajan P., and Bhatnagar N. Micro-mechanical modeling of machining of FRP composites - cutting force analysis. Compos Sci Technol 67 11-12 (2007) 579-593
23. Venu Gopala Rao G., Mahajan P., and Bhatnagar N. Machining of UD-GFRP composites chip formation mechanism. Compos Sci Technol 67 11-12 (2007) 2271-2281
24. Mkaddem A., Demirci I., and El Mansori M. A micro-macro combined approach using FEM for modelling of machining of FRP composites: Cutting forces analysis. Composites Science and Technology 68 15-16 (2008) 3123-3127
25. ABAQUS, Inc. Analysis user's manual. Version 6.6. USA; 2006.
26. Liu Jie X., Davim J.P., and Cardoso R. Prediction on tribological behaviour of composite PEEK-CF30 using artificial neural networks. J Mater Process Technol 189 1-3 (2007) 374-378
27. Zitoune R., Collombet F., Lachaud F., Piquet R., and Pasquet P. Experiment-calculation comparison of the cutting conditions representative of the long fibre composite drilling phase. Compos Sci Technol 65 3-4 (2005) 455-466