Analysis of the influence of tool type, coatings, and machinability on the thermal fields in orthogonal machining of AISI 4140 steels

CIRP Annals - Manufacturing Technology

Volumn 58, Issue 1, 2009, Pages 85-88

  Arrazola, P J ^a   Arriola, I ^a,b   Davies, M A ^c  

^a MONDRAGON UNIVERSITY   (Spain)

^b marGUNE Center   (Spain)

^c The University of North Carolina at Charlotte   (United States)

Author keywords

Energy balance; Machinability; Temperature

Indexed keywords

AISI 4140 STEELS; CHIP BREAKERS; CONTROL VOLUMES; CUTTING POWER; DIRECT MEASUREMENTS; ENERGY PARTITIONS; ORTHOGONAL CUTTINGS; ORTHOGONAL MACHINING; PHYSICAL TOOLS; RAKE ANGLES; SUB SURFACE DAMAGES; THERMAL FIELDS; THERMAL IMAGES; THERMAL IMAGING; TOOL WEARS; WORK PIECES;

ENERGY BALANCE;

EID: 67349086200     PISSN: 00078506     EISSN: 17260604     Source Type: Journal    
DOI: 10.1016/j.cirp.2009.03.085     Document Type: Article

References (15)

1. Sartkulvanich P., Koppka F., and Altan T. Determination of Flow Stress for Metal Cutting Simulation-A Progress Report. Journal of Materials Processing Technology 146 (2004) 61-71
2. Wright P.K. Correlation of Tempering Effects with Temperature Distribution in Steel Cutting Tools. Journal of Engineering for Industry 100 (1978) 131-136
3. Leshock C.E., and Shin Y.C. Investigation on Cutting Temperature in Turning by a Tool-Work Thermocouple Technique. Journal of Manufacturing Science and Engineering 119 (1997) 502-508
4. Barrow G. A Review of Experimental and Theoretical Techniques for Assessing Cutting Temperatures. Annals of the CIRP 22 2 (1973) 203-211
5. Fleischer J., Pabst R., and Kelemen S. Heat Flow Simulation for Dry Machining of Power Train Castings. Annals of the CIRP 56 1 (2007) 117-122
6. Outeiro J.C., Pina J.C., M'Saoubi R., Pusavec F., and Jawahir I.S. Analysis of Residual Stresses Induced by Dry Turning of Difficult-to-Machine Materials. Annals of the CIRP 57 1 (2008) 77-80
7. Arrazola P.J., Arriola I., Davies M.A., Cooke A.L., and Dutterer B.S. The Effect of Machinability on Thermal Fields in Orthogonal Cutting of AISI 4140 Steel. Annals of the CIRP 57 1 (2008) 65-68
8. Davies M.A., Yoon H., Schmitz T.L., Burns T.J., and Kennedy M.D. Calibrated Thermal Microscopy of the Tool-Chip Interface in Machining. Machining Science and Technology 48 2 (2003) 167-190
9. Wanigarathne P.C., Kardekar A.D., Dillon Jr. O.W., Poulachon G., and Jawahir I.S. Progressive Tool-wear in Machining with Coated Grooved Tools and its Correlation with Cutting Temperature. Journal of Wear 259 (2005) 1215-1224
10. Grzesik W., and Van Luttervelt C.A. Analytical Models Based on Composite Layer for Computation of Tool-Chip Interface Temperatures in Machining Steels with Multilayer Coated Cutting Tools. Annals of the CIRP 54 1 (2005) 91-94
11. Denkena B., Rudzio H., and Brandes A. Study of the Influence of the Cutting Edge Microgeometry on the Cutting Forces and Wear in Turning Operations. 8th Workshop on Modelling of Machining Operations (2005) 503-508
12. Grzesik W., and Nieslony P. A Computational Approach to Evaluate Temperature and Heat Partition in Machining with Multilayer Coated Tools. International Journal of Machine Tools & Manufacture 43 (2003) 1311-1317
13. Hamann J.-C., Grolleau V., and Le Maître F. Machinability Improvement of Steels at High Cutting Speeds-study of Tool/Work Material Interaction. Annals of CIRP 45 1 (1996) 87-92
14. Arrazola P.J., Ugarte D., and Domínguez X. A New Approach for the Friction Identification During Machining Through the Use of Finite Element Modelling. International Journal of Machine Tools & Manufacture 48 (2008) 73-183
15. Attia M.H., and Kops L. A New Approach to Cutting Temperature Prediction Considering the Thermal Constriction Phenomenon in Multi-layer Coated Tools. Annals of the CIRP 53 1 (2004) 47-52