Dry sliding wear of Al alloy/SiCp functionally graded composites: Influence of processing conditions

Wear

Volumn 267, Issue 1-4, 2009, Pages 585-592

  Vieira, A C ^a   Sequeira, P D ^a   Gomes, J R ^a   Rocha, L A ^a  

^a UNIVERSITY OF MINHO   (Portugal)

Author keywords

Al alloy SiCp composites; Dry sliding wear; FGM; MML

Indexed keywords

AL ALLOY/SICP COMPOSITES; AL ALLOYS; ALUMINIUM MATRIX COMPOSITES; AVERAGE GRAIN SIZE; CAST RINGS; CHROMIUM STEEL; DRY SLIDING; DRY SLIDING WEAR; FGM; FUNCTIONALLY GRADED; GOOD CORRELATIONS; MATRIX; MML; PROCESSING CONDITION; PROCESSING PARAMETERS; RADIAL GEOMETRIES; REINFORCING PARTICLES; RING CONFIGURATION; ROOM TEMPERATURE; ROTATING SPEED; SIC PARTICLES; SLIDING WEAR; SLIDING WEAR BEHAVIOUR; WEAR MECHANISMS;

ALUMINUM; CENTRIFUGAL CASTING; CENTRIFUGATION; CHROMIUM; REINFORCEMENT; SILICON CARBIDE; TRIBOLOGY; WEAR OF MATERIALS;

METALLIC MATRIX COMPOSITES;

EID: 65749118389     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2009.01.041     Document Type: Article

References (23)

1. p-reinforced functionally graded composites. Materials Science Forum 871 (2004) 455-456
2. Miracle D.B. Metal matrix composites - from science to technological significance. Composites Science and Technology 65 (2005) 2526-2540
3. Das S. Development of aluminium alloy composites for engineering applications. Transactions of the Indian Institute of Metals 57 4 (2004) 325-334
4. Watanabe Y., Kawamoto A., and Matsuda K. Particle size distributions in functionally graded materials fabricated by the centrifugal solid-particle method. Composites Science and Technology 62 (2002) 881-888
5. Royer A., and Vasseur S. In: Stefanescu D.M. (Ed). Casting, Metals Handbook,. 9th ed. vol.15 (1988), ASM International, Ohio pp. 296
6. Fukui Y. Optimization of the In Situ Al-Si Base Functionally Graded Material Fabricated by Centrifugal Casting. JSME International Jouranl Series III 34 (1991) 144
7. Watanabe Y., Yamanaka N., and Fukui Y. Control of composition gradient in a metal-ceramic functionally graded material manufactured by the centrifugal method. Composites Part A 29A (1998) 595
8. Vieira A.C., Rocha L.A., and Gomes J.R. Influence of SiC particles incorporation on the microstructure and tribological behaviour of functional graded Al/SiCp composites. Proceedings of the IV Iberian Congress on Tribology, Ibertrib 2007. Bilbao, Spain, June (2007)
9. Gul F., and Acilar M. Effect of the reinforcement volume fraction on the dry sliding wear behavior of Al-10Si/SiCp composites produced by vacuum infiltration technique. Composite Science and Technology 64 (2004) 1959-1970
10. Acilar M., and Gul F. Effect of the applied load, sliding distance and oxidation on the wear behavior of Al-10Si/SiCp composites produced by vacuum infiltration technique. Materials and Design 25 (2004) 209-217
11. Mondal D.P., Das S., Rao R.N., and Singh M. Effect of SiC addition and running-in-wear on the sliding wear behaviour of Al-Zn-Mg aluminium alloy. Materials Science and Engineering A 402 (2005) 307-319
12. Mondal D.P., and Das S. High stress abrasive wear behaviour of aluminium hard particle composites: Effect of experimental parameters, particle size and volume fraction. Tribology International 39 (2006) 470-478
13. Gomes J.R., Miranda A.S., Rocha L.A., and Silva R.F. Effect of Functionally Graded Properties on the Tribological Behaviour of Aluminium Matrix Composites. Key Engineering Materials 230-232 (2002) 271-274
14. Gomes J.R., Rocha L.A., Crnkovic S.J., Silva R.F., and Miranda A.S. Friction and Wear Properties of Functionally Graded Aluminum Matrix Composites. Materials Science Forum 423-425 (2003) 91
15. Zang L., He X.B., Qu X.H., Duan B.H., Lu X., and Qin M.L. Dry sliding wear properties of high volume fraction SiCp/Cu composites produced by pressureless infiltration. Wear 265 (2008) 1848-1856
16. Li X.Y., and Tandon K.N. Microstructural characterization of mechanically mixed layer and wear debris in sliding wear of an Al alloy and an Al based composite. Wear 245 (2000) 148-161
17. Asthana R. Review: Reinforced cast metals; Part I Solidification microstructure. Journal of Materials Science 33 (1998) 1679-1698
18. Uresh S., and Mortensen A. Fundamentals of Functionally Graded Materials: Processing and Thermomechanical Behaviour of Graded Metals and Metal-Ceramic Composites (1998), IOM Communications Ltd.
19. Gao J.W., and Wang C.Y. Modeling the solidification of functionally graded materials by centrifugal casting. Materials Science and Engineering A292 (2000) 207-215
20. Hutchings I.M. Tribology: friction and wear of engineering materials. Metallurgy & Materials Science Series (2001), Butterworth-Heinemann Publications
21. Venkataraman B., and Sundararajan G. Correlation between the characteristics of the mechanically mixed layer and wear behaviour of aluminium, Al-7075 alloy and Al-MMCs. Wear 245 (2000) 22-38
22. Deui R.L., Subramanian C., and Yellup J.M. Dry sliding wear of aluminium composites - A review. Composites Science and Technology 57 (1997) 415-435
23. Singh M., Manurung P., and Low I.M. Depth profiling of near-surface information in a functionally graded alumina/aluminium titanate composite using grazing-incidence synchrotron radiation diffraction. Materials Letters 55 (2002) 344-349