Slurry wear characteristics of zinc-based alloys: Effects of sand content of slurry, silicon addition to alloy system and traversal distance

Transactions of Nonferrous Metals Society of China (English Edition)

Volumn 19, Issue 2, 2009, Pages 277-286

  PRASAD, B K ^a   MODI, O P ^a  

^a REGIONAL RESEARCH LABORATORY CSIR   (India)

Author keywords

erosion corrosion abrasion; material removal mechanisms; microstructure property correlations; slurry wear behaviour; zinc based alloys

Indexed keywords

ALLOY SYSTEMS; CONCENTRATION OF; EROSION-CORROSION-ABRASION; EXPERIMENTAL CONDITIONS; MATERIAL REMOVAL MECHANISMS; MICROCONSTITUENTS; SAND CONCENTRATIONS; SAND CONTENTS; SAND MEDIAS; SAND PARTICLES; SILICON ADDITIONS; SILICON FREE ALLOYS; SUBSURFACE REGIONS; SULPHURIC ACIDS; TEST ENVIRONMENTS; WEAR CHARACTERISTICS; WEAR RATES; WEAR RESPONSE; WEAR TESTS;

ABRASION; CHEMICAL ANALYSIS; CORROSION RESISTANCE; DISSOLUTION; ELECTROLYSIS; ELECTROLYTES; EROSION; LIQUIDS; MICROSTRUCTURE; NONMETALS; SAND; SLURRIES; SODIUM; SODIUM CHLORIDE; SULFURIC ACID; ZINC; ZINC ALLOYS;

SILICON ALLOYS;

EID: 64149094590     PISSN: 10036326     EISSN: None     Source Type: Journal    
DOI: 10.1016/S1003-6326(08)60265-4     Document Type: Article

References (79)

1. CALAYAG T.S. Zinc alloys replace bronze in mining equipment bushings and bearings [J]. Mining Engineering 36 (1983) 727-728
2. PRATT G.C. Materials for plain bearings [J]. International Materials Review 18 (1973) 1-27
3. KUBEL E.J. Expanding horizons for ZA alloys [J]. Advanced Materials and Processes 132 (1987) 51-57
4. RAUSCH W. Chemical surface treatment of steel coated with zinc and zinc alloys [C]. Proceedings of the International Conference of Zinc and Zinc Alloy Coated Steel Sheet (GALVATECH) (1989), The Iron and steel Institute of Japan, Tokyo, Japan 199-201
5. SHIN J C, LEE Y P, CHOI K D, JUN J H. Proceedings of the International Conference of Zinc and Zinc Alloy Coated Steel Sheet (GALVATECH), Amsterdam, The Netherlands, Sept. 8-10, 1992.
6. WALLINDER I.O., LEYGRAF C., KARLEN C., HEIJORICK D., and JANSSEN C.R. Atmospheric corrosion of zinc-based materials: Run off rates, chemical speciation and ecotoxicity effects [J]. Corrosion Science 43 (2001) 809-816
7. ISHIKAWA T., UEDA M., KANDORI K., and NAKAYAMA T. Air permeability of the artificially synthesized Zn-Al-Mg alloy rusts [J]. Corrosion Science 49 (2007) 2547-2556
8. TACHIBANA K., MORINAGA Y., and MAYUZUMI M. Hot dip fine Zn and Zn-Al alloy double coating for corrosion resistance at coastal area [J]. Corrosion Science 49 (2007) 149-157
9. MOEIRA A.R., PANOSSIAN Z., CAMARGO P.L., MOEIRA M., DE SILVA I.C., and DE CARVALHO J. Zn/55Al coating microstructure and corrosion mechanism [J]. Corrosion Science 48 (2006) 564-576
10. DALLEDONE E., BARBOSA M.A., and WOLYMEC S. Zinc-55%Al-1.6%Si coating compared with zinc coating [J]. Materials Performance 34 7 (1995) 24-28
11. ALLEGRA L, DUTTON R J, HUMAYUN A. Proceedings of the 1st Intergalva Conference. Munich, Germany, 1985: A/1-A/6.
12. CHEN W., LIU Q., ZHU L., and WANG L. A combinatorial study of the corrosion and mechanical properties of Zn-Al material library fabricated by ion beam sputtering [J]. Journal of Alloys and Compounds 459 (2008) 261-266
13. DAFYDD H., WORSLEY D.A., and MCMURRAY H.N. The kinetics and mechanism of cathodic oxygen reduction on zinc and zinc-aluminium alloy galvanized coatings [J]. Corrosion Science 47 (2005) 3006-3018
14. PRUTHVIRAJ R.D., KRUPAKARA P.V., and NAGASWARUPA H.P. Open circuit potential studies of ZA-27/SiC MMCs in acid choloride media [J]. Transactions of the Society of Electrochemical Science and Technology 41 (2006) 94-96
15. PRUTHVIRAJ R.D., and KRUPAKARA P.V. A study on corrosion behaviour of ZA-27/Sic composite at higher temperature in acidic medium using autoclave [J]. Research Journal of Chemistry and Environment 10 (2006) 71-75
16. KRUPAKARA P.V., MANJUNATH S., and UCHIL J. Characterization of corrosion properties of ZA-27/quartz metal matrix composites [C]. Proceedings of Processing Materials for Properties 2000 (2000), TMS, San Francisco 113-116
17. PACIEJ R.C., and AGGARWALA V.S. Metallurgical variables influencing the corrosion susceptibility of a powder metallurgy SiCw/Al composite [J]. Corrosion 42 (1986) 718-728
18. SUN H., KOO E.Y., and WHEAT D.H.G. Corrosion behavior of SiCP/6061 Al metal matrix composites [J]. Corrosion 47 (1991) 741-753
19. TRZASKOMA P.P. Pit morphology of aluminium alloy and silicon carbide/aluminium alloy metal matrix composites [J]. Corrosion 46 (1990) 402-409
20. OSARIO W.R., FREIRE C.M., and GARCIA A. The effect of dendritic microstructure on the corrosion resistance of Zn-Al alloys [J]. Journal of Alloys and Compounds 397 (2005) 179-191
21. OSARIO W.R., GOULART P.R., SANTOS G.A., NETCO C.M., and GARCIA A. Effect of dendritic arm spacing on mechanical properties and corrosion resistance of Al-9 wt pct Si and Zn-27 wt pct Al alloys [J]. Metallurgical and Materials Transactions A 37A (2006) 2525-2538
22. PRASAD B.K. Tensile properties of some zinc-based alloys comprising 27.5% Al: Effects of alloy composition, microstructure and test conditions [J]. Mater Sci Eng A 245A (1998) 257-266
23. PRASAD B.K. Response of some cast zinc-37.5%Al-based alloys comprising nickel/silicon under different tensile loading conditions [J]. Journal of Materials Engineering and Performance 7 (1998) 632-636
24. PRASAD B.K. Mechanical properties and sliding wear characteristics of zinc-based alloys: Effects of partially substituting copper by silicon [J]. Zeitschrift fur Metallkunde 88 (1997) 929-933
25. PRASAD B.K. Effects of silicon addition and test parameters on the sliding wear characteristics of zinc-based alloy containing 37.5% aluminium [J]. Materials Transactions of the Japan Institute of Metals 38 (1997) 701-706
26. SAVASKAN T., and MURPHY S. Mechanical properties and lubricated wear of Zn-25 Al based alloys [J]. Wear 116 (1987) 211-224
27. MURPHY S., and SAVASKAN T. Comparative wear behaviour of Zn-Al based alloys in an automotive engine application [J]. Wear 98 (1984) 151-161
28. PRASAD B.K., PATWARDHAN A.K., and YEGNESWARAN A.H. Microstructure-property characterization of some zinc-based alloys: Effects of heat treatment parameters [J]. Zeitschrift fur Metallkunde 87 (1996) 967-971
29. JIAN L., LAUFER E.E., and MASOUNAIVE J. Wear in Zn-Al-Si alloys [J]. Wear 165 (1993) 51-56
30. PRASAD B.K. Effect of heat treatment on tensile properties of zinc-37.5 mass % aluminium alloy containing nickel or silicon [J]. Materials Transactions of the Japan Institute of Metals 39 (1998) 387-390
31. LEE P.P., SAVASKAN T., and LAUFER E. Wear resistance and microstructure of Zn-Al-Si and Zn-Al-Cu alloys [J]. Wear 117 (1987) 79-89
32. PRASAD B.K. Wear response of a zinc-based alloy containing silicon as influenced by material microstructure and test conditions [J]. Mater Sci Eng A 367A (2004) 63-73
33. SAVASKAN T., and ADYMER A. Effect of silicon content on the mechanical properties of monotectoid-based zinc-aluminium-silicon alloys [J]. Wear 257 (2004) 377-388
34. SAVASKAN T., and BICAN O. Effect of silicon content on the microstructural features and mechanical and sliding wear properties of Zn-40Al-2Cu-(0-5)Si [J]. Mater Sci Eng A 404A (2005) 259-269
35. PRASAD B.K. Effects of partially substituting copper by silicon on the physical, mechanical and wear properties of a Zn-37.5%Al-based alloy [J]. Materials Characterization 44 (2000) 301-308
36. PURCEK G., SAVASKAN T., and MURPHY S. Dry sliding friction and wear properties of zinc-based alloys [J]. Wear 252 (2002) 894-901
37. SAVASKAN T., TURHAL M.S., and MURPHY S. Effects of cooling rate on structure and mechanical properties of monotectoid zinc-aluminium alloys [J]. Materials Science and Technology 19 (2003) 67-74
38. AZAKLI Z., and SAVASKAN T. An examination of friction and sliding wear properties of Zn-40Al-2Cu-2Si alloy in case of oil cut-off [J]. Tribology International 41 (2008) 9-16
39. SAVASKAN T., and AZAKLI Z. An investigation of lubricated friction and wear properties of Zn-40Al-2Cu-2Si alloy in comparison with SAE65 bearing bronze [J]. Wear 264 (2008) 920-928
40. SAVASKAN T., KUCOMEROGLU A.P., and PURCEK G. Effects of copper content on the mechanical and sliding wear properties of monotectoid-based zinc-aluminium alloys [J]. Tribology International 37 (2004) 45-50
41. PRASAD B.K., PATWARDHAN A.K., and YEGNESWARAN A.H. Influence of heat treatment parameters on the microstructure and properties of some zinc-based alloys [J]. Journal of Materials Science 31 (1996) 6317-6324
42. PRASAD B.K., MODI O.P., JHA A.K., DASGUPTA R., DAS S., MONDAL D.P., and YEGNESWARAN A.H. Erosion-corrosion-abrasion characteristics in slurry of a zinc-based alloy and Its composite containing alumina particle dispersoid [J]. Materials Science and Technology 17 (2001) 1444-1450
43. AYLOR D.M., and MORAN P.J. Effect of reinforcement on the pitting behaviour of Al-base MMCs [J]. Journal of the Electrochemical Society 132 (1985) 1277-1281
44. MODI O.P., SAXENA M., PRASAD B.K., YEGNESWARAN A.H., and VAIDYA M.L. Corrosion behaviour of squeeze cast aluminium alloy-silicon carbide composites [J]. Journal of Materials Science 27 (1992) 3897-3902
45. SAXENA M., MODI O.P., PRASAD B.K., and JHA A.K. Erosion-corrosion characteristics of an aluminium alloy-alumina fibre composite [J]. Wear 169 (1993) 119-124
46. TURENE S., SIMARD D., and FISSET M. Influence of structural parameters on the slurry erosion resistance of squeeze cast metal matrix composite [J]. Wear 149 (1991) 187-197
47. TURENE S., CHATIGNY Y., SIMARD D., VARON S., and MASOUNAIVE J. The effect of abrasive particles on the slurry erosion resistance of particulate reinforced aluminium alloy [J]. Wear 141 (1990) 147-158
48. Levy A.V. Erosion and erosion-corrosion of metals [J]. Corrosion 51 (1995) 872-883
49. MONDAL D.P., DAS S., and PRASAD B.K. Study of erosive-corrosive wear behaviour of an aluminium alloy composite through factorial design of experiments [J]. Wear 217 (1998) 1-6
50. DASGUPTA R., PRASAD B.K., JHA A.K., MODI O.P., DAS S., and YEGNESWARAN A.H. Slurry erosive wear characteristics of a hardfaced steel: Effect of experimental parameters [J]. Wear 213 (1997) 41-46
51. RAMULU M., RAJU S.P., INOU H., and ZENG J. Hydro abrasive-erosive characteristics of 30 vol.% SiC/6061-T6 Al composite at shallow impact angles [J]. Wear 166 (1993) 55-63
52. JI J.L., and JANG J.L. Wear corrosion behaviour of cast-in composite reinforced by WC particles [J]. Wear 138 (1990) 23-32
53. LI Y., BURSTEIN G.T., and HUTCHINGS I.M. Influence of environmental composition and electrochemical potential on the slurry erosion-corrosion of aluminium [J]. Wear 1818/183 (1995) 70-79
54. TOMILSON W., and MATHEWS S.J. Cavitation erosion-corrosion of aluminium alloy matrix/ceramic composites [J]. Journal of Materials Science Letters 13 (1994) 170-173
55. DAS S., MONDAL D.P., DASGUPTA R., and PRASAD B.K. Mechanism of material removal during erosion-corrosion of an Al-SiC particle composite [J]. Wear 236 (1999) 295-302
56. YU S.Y., ISHI H., and CHUANG T.H. Corrosive wear of SiC whisker- and particulate reinforced 6061 aluminium alloy composites [J]. Metallurgical and Materials Transactions A 27A (1996) 2653-2662
57. ASTM Standards Designation G119-93. Standard Guide for Determining Synergism between Wear and Corrosion [R]. ASTM Standards, 1993: 139-144.
58. PRASAD B.K. Effects of alumina dispersion on the erosive-corrosive wear response of a zinc-based alloy under changing slurry conditions and distance [J]. Wear 238 (2000) 151-159
59. PRASAD B.K., MODI O.P., JHA A.K., and YEGNESWARAN A.H. Effect of sand concentration in the medium and traversal distance and speed on the slurry wear response of a zinc-based alloy alumina particle composite [J]. Tribology Letters 17 (2004) 301-309
60. PRASAD B.K., MODI O.P., JHA A.K., and PATWARDHAN A.K. Effects of some material and experimental variables on the slurry wear characteristics of zinc-aluminium alloys [J]. Journal of Materials Engineering and Performance 10 (2001) 75-80
61. NEVILLE A., HODGKIESS T., and DALLAS J.T. A study of the erosion-corrosion behavior of engineering steels for marine pumping applications [J]. Wear 186/187 (1995) 497-507
62. BURSTEIN G.T., LI Y., and HUTCHINGS I.M. The influence of corrosion on the erosion of aluminum by aqueous silica slurries [J]. Wear 186/187 (1995) 515-522
63. POSTLETHWAITE J. Effect of chromate inhibitor on the mechanical and electrochemical components of erosion-corrosion in aqueous slurries of sand [J]. Corrosion 37 (1981) 1-5
64. MATSUMURA M., OKA Y., HIURA H., and YANO M. The role of passivating film in preventing slurry erosion-corrosion of austenitic stainless steel [J]. ISIJ International 31 2 (1991) 168-176
65. NEVILLE A., REYS M., and XU H. Examining corrosion effects and corrosion/erosion interactions on metallic materials in aqueous slurries [J]. Tribology International 35 (2002) 643-650
66. MALKA R., NESIC S., and GULINO D.A. Erosion-corrosion and synergistic effects in disturbed liquid particle flow [J]. Wear 262 (2007) 791-799
67. WU J.K., and HSU Y.S. Electrochemical corrosion of zinc in sodium chloride [J]. Journal of Materials Science 21 (1986) 3475-3478
68. DE LA FUENTE D., CASTARIO J.G., and MOROULO M. Long term atmospheric corrosion of zinc [J]. Corrosion Science 49 (2007) 1420-1436
69. FARR J.P.G., and HAMPSON N.A. Reactions at solid metal electrodes Part 1-Faradaic impedance of zinc electrodes in alkaline solution [J]. Transactions of The Faraday Society 62 (1966) 3493-3501
70. FARR J.P.G., and HAMPSON N.A. Evaluation of the characteristics of exchange reactions (1): Exchange reaction at a solid zinc electrode in alkali [J]. Transactions of Electroanalytical Chemistry 13 (1967) 433-441
71. VAN DORNE W., and DIRKSE T.P. Supersaturated zincate solutions [J]. Journal of the Electrochemical Society 122 (1975) 1-4
72. BALL A., and WARD J.J. An approach to material selection for corrosive-abrasive wear by systematic in-situ and laboratory testing procedures [J]. Tribology International 85 (1986) 347-351
73. ZHOU S., STACK M.M., and NEWMAN R.C. Characterization of synergistic effects between erosion and corrosion in an aqueous environment using electrochemical techniques [J]. Corrosion 52 (1996) 934-946
74. QUINTANA P., VELEVA L., CAUICH W., POMES R., and PENE J.L. Study of the composition and morphology of initial stages of corrosion products formed on Zn plates exposed to the atmosphere of southeast Mexico [J]. Applied Surface Science 99 (1996) 325-334
75. PRASAD B.K., PATWARDHAN A.K., and YEGNESWARAN A.H. Microstructural features controlling the sliding wear response of some bearing alloys [J]. Zeitschrift fur Metallkunde 88 (1997) 774-780
76. PROTOPOPOFF E., and MARCUS P. Electrode potentials [M] Vol. 13A (2003), Corrosion-Fundamentals, Testing and Protection, Handbook of Metals 8-12 ASM, Materials Park, Ohio, USA.
77. In: BRANDES E.A. (Ed). Smithells metals reference book [M]. 6th ed. (1983), Butterworths, London 370-801
78. PRASAD B.K., PATWARDHAN A.K., and YEGNESWARAN A.H. Dry sliding wear characteristics of some zinc-aluminium alloys: A comparative study with a bearing bronze at a slow speed [J]. Wear 199 (1996) 142-151
79. PRASAD B.K., PATWARDHAN A.K., and YEGNESWARAN A.H. Factors controlling the dry sliding wear behaviour of a leaded-tin bronze [J]. Materials Science and Technology 12 (1996) 427-435