Metallurgical factors affecting failure mode of resistance spot welds

Materials Science and Technology Conference and Exhibition, MS and T'08

Volumn 4, Issue , 2008, Pages 2465-2473

  Pouranvari, M ^a   Marashi, P ^b   Goodarzi, M ^c   Bahmanpour, H ^d  

^a ISLAMIC AZAD UNIVERSITY   (Iran)

^b AMIRKABIR UNIVERSITY OF TECHNOLOGY   (Iran)

^c IRAN UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Iran)

^d Wayne State University   (United States)

Author keywords

Advanced high strength steel (AHSS); Failure mode; Fusion zone size; Resistance spot welding

Indexed keywords

ADVANCED HIGH STRENGTH STEEL (AHSS); ANALYTICAL MODELS; FAILURE MECHANISMS; FUSION ZONE SIZE; FUSION ZONES; PULL-OUT FAILURES; RESISTANCE SPOT WELDING; RESISTANCE SPOT WELDS; SHEET THICKNESS; SPOT WELDS; TENSILE-SHEAR TESTS; WELD MICROSTRUCTURES;

FAILURE MODES; HARDNESS; METALLURGY; RESISTANCE WELDING; SPOT WELDING; STEEL; STRENGTH OF MATERIALS; WELDING;

WELDS;

EID: 63749100095     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (13)

1. Alenius M., Pohjanne P., Somervuorl M., Hanninen H, Exploring the Mechanical Properties of Spot Welded Dissimilar Joints for Stainless and Galvanized Steels, Weld. J., Vol.87, 2007, p 305s-313s.
2. Marashi P., Pouranvari M., Amirabdollahian S., Abedi A., Goodarzi M., Microstructure and Failure Behavior of Dissimilar Resistance Spot Welds between Low Carbon Galvanized and Austenitic Stainless Steels, Mater. Sci Eng. A, Vol480,2008, p 175-180.
3. Chao Y J, Failure Mode of Resistance Spot Welds: Interfacial versus Pullout, Sci. Technol. Weld. Joining, Vol. 8, 2003, pl33-137.
4. Pouranvari M., Asgari H. R., Mosavizadeh S. M., Marashi P. H, Goodarzi M., Effect of Weld Nugget Size on Overload Failure Mode of Resistance Spot Welds, Sci. Technol. Weld. Joining, Vol.12, p217-225.
5. Recommended Practices for Test Methods and Evaluation the Resistance Spot Welding Behavior of Automotive Sheet Steels, ANSI/AWS/SAE D8.9-97.
6. M. Marya, K. Wang, L. G. Hector, X. Gayden, Tensile-Shear Forces and Fracture Modes in Single and Multiple Weld Specimens in Dual-Phase Steels, J. Manufac. Sci. Eng., p 287-298
7. X.Sun, E.V.Stephens, M.A. Khaleel, Effects of Fusion Zone Size and Failure Mode on Peak ^Load and Energy Absorption of Advanced High Strength Steel Spot Welds under Lap Shear 'Leading Conditions, Eng. Fail. Anal., Vol.15, 2008, p356-367.
8. Deng X^Ch'eri W., Shi G., Three-dimensional finite element analysis of the mechanical behavior of spot welds, Finite element in analysis and design, Vol.35, 2000, p 17-39.
9. Y. J. Chao, Ultimate Strength and Failure Mechanism of Resistance Spot Weld Subjected to Tensile, Shear, or Combined Tensile/Shear Loads, ASME. J. Eng. Mater. Technol., Vol.125, 2003, p 1-8
10. S. Zunigavand S. D. Sheppard: in 'Fatigue and fracture mechanics',Vol. 27, ASTM STP 1296, (ed. R. S; Piascik et al.), 469-89; 1997, Philadephic, USA, ASTM.
11. Lin P.C., Lin S.H., Pan J., Modeling of Failure near Spot Welds in Lap-Shear Specimens, Based on a Plane Stress Rigid Inclusion Analysis, Eng. Frac. Mech., Vol. 73, 2006, p 2229-2249.
12. Sun, E. V. Stephens, R. W. Davies, M. A. Khaleel and D. J.Spinella, Effects of Fusion Zone Size on Failure Modes and Static Strength of Aluminum Resistance Spot Welds, Weld. J., Vol. 83, 2004, ppl88s-195s.
13. Satoh T, Abe H, Nishikawa K, Morita M. On three-dimensional elastic-plastic stress analysis of spot-welded joint under tensile shear load, Trans Jpn Weld Soc, Vol. 22, 1991, p 46-51.