Analysis of the tip roundness effects on the micro- and macroindentation response of elastic-plastic materials

Journal of Materials Research

Volumn 24, Issue 3, 2009, Pages 1037-1044

  Rodríguez Pulecio, Sara Aida ^a   Moré Farias, María Cristina ^a   Souza, Roberto Martins ^a  

^a UNIVERSITY OF SÃO PAULO   (Brazil)

Author keywords

[No Author keywords available]

Indexed keywords

AREA CALCULATIONS; CORRECTION FACTORS; ELASTIC-PLASTIC MATERIALS; FINITE ELEMENT CALCULATIONS; FINITE-ELEMENT MODELING; HARDNESS VALUES; INDENTATION CURVES; INDENTER; MACRO INDENTATIONS; MATERIAL PROPERTIES; OLIVER-PHARR METHODS; PENETRATION DEPTHS; PHARR METHODS; PLASTIC WORKS; TIP RADIUS; TOTAL WORKS; UNLOADING SLOPES;

HARDNESS; MECHANICAL PROPERTIES; UNLOADING; VICKERS HARDNESS TESTING;

PLASTICS;

EID: 63149151180     PISSN: 08842914     EISSN: None     Source Type: Journal    
DOI: 10.1557/jmr.2009.0078     Document Type: Article

References (33)

1. W.C. Oliver and G.M. Pharr: An improved technique for determining hardness and elastic modulus using load and sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).
2. J.M. Antunes, A. Cavaleiro, L.F. Menezes, M.I. Simões, and J.V. Fernandes: Ultra-microhardness testing procedure with Vickers indenter. Surf. Coat. Technol. 149, 27 (2002).
3. M.R. VanLandingham, T.F. Juliano, and M.J. Hagon: Measuring tip shape for instrumented indentation using atomic force microscopy. Meas. Sci. Technol. 16, 2173 (2005).
4. W. Chen, M. Li, I. Zhang, Y.T. Cheng, and C.M. Cheng: Influence of indenter tip roundness on hardness behavior in nanoindentation. Mater. Sci. Eng. A, 445-446, 323 (2007).
5. D. Ma, C.W. Ong, and S.F. Wong: New relationship between Young's modulus and nonideally sharp indentation parameters. J. Mater. Res. 19(7), 2144 (2004).
6. D. Ma, C.W. Ong, and T. Zhang: An improved energy method for determining Young's modulus by instrumented indentation using a Berkovich tip. J. Mater. Res. 23(8), 2106 (2008).
7. K.D. Bouzakis, N. Michailidis, S. Hadjiyiannis, G. Skordaris, and G. Erkens: The effect of specimen roughness and indenter tip geometry on the determination accuracy of thin hard coatings stress-strain laws by nanoindentation. Mater. Char. 49, 149 (2003).
8. J.M. Meza and E.J. Cruz: Tip roundness effect in mechanical properties measured by instrumented indentation. Sci. Teach. 36, 613 (2007).
9. J.M. Antunes, L.F. Menezes, and J.V. Fernandes: Three-dimensional numerical simulation of Vickers indentation tests. Int. J. Solids Struct. 43, 784 (2006).
10. J.M. Meza, F. Abbes, and M. Troyon: Penetration depth and tip radius dependence on the correction factor in nanoindentation measurements. J. Mater. Res. 23, 725 (2008).
11. M. Troyon and L. Huang: Correction factor for contact area in nanoindentation measurements. J. Mater. Res. 20, 610 (2005).
12. M. Troyon and S. Lafaye: About the importance of introducing a correction factor in the Sneddon relationship for nanoindentation measurements. Philos. Mag. 86, 5299 (2006).
13. M. Dao, N. Chollacoop, K.J. Van Vliet, T.A. Venkatesh, and S. Suresh: Computational modeling of the forward and reverse problems in instrumented sharp indentation. Acta Mater. 49, 3899 (2001).
14. J.L. Bucaille, S. Stauss, E. Felder, and J. Michler: Determination of plastic properties of metals by instrumented indentation using different sharp indenter. Acta Mater. 51, 1663 (2003).
15. Y.T. Cheng and C.M. Cheng: Scaling, dimensional analysis, and indentation measurements. Mater. Sci. Eng. R, 44, 91 (2004).
16. O. Casals and J. Alcalá: The duality in mechanical property extractions from Vickers and Berkovich instrumented indentation experiments. Acta Mater. 53, 3545 (2005).
17. Y.T. Cheng and C.M. Cheng: Further analysis of indentation loading curves: Effects of tip rounding on mechanical property measurements. J. Mater. Res. 13, 1059 (1998).
18. J. Chen and S.J. Bull: On the relationship between plastic zone radius and maximum depth during nanoindentation. Surf. Coat. Technol. 201, 4289 (2006).
19. M. Mata and J. Alcalá: Mechanical property evaluation through sharp indentations in elastoplastic and fully plastic contact regimes. J. Mater. Res. 18(7), 1705 (2003).
20. S. Suresh and A.E. Giannakopoulos: A new method for estimating residual stresses by instrumented sharp indentation. Acta Mater. 46, 5755 (1998).
21. I.N. Sneddon: The relationship between load and penetration in the axisimetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).
22. R.B. King: Elastic analysis of some punch problems for a layered medium. Int. J. Solids Struct. 23, 12 (1987) 1657.
23. J.C. Hay, A. Bolshakov, and G.M. Pharr: A critical examination of the fundamental relations used in the analysis of nanoindentation data. J. Mater. Res. 14(6), 2296 (1999).
24. M. Li, W.M. Chen, N.G. Liang, and L.D. Wang: A numerical study of indentation using indenters of different geometry. J. Mater. Res. 19, 73 (2004).
25. M. Mata and J. Alcalá: The role of friction on sharp indentation. J. Mech. Phys. Solids 52, 145 (2004).
26. S. Swaddiwudhipong, J. Hua, K.K. Tho, and Z.S. Liu: Equivalency of Berkovich and conical load-indentation curves. Modell. Simul. Mater. Sci. Eng. 14, 71 (2006).
27. Theory Manual 5.1-1, Abaqus, Version 6.7.
28. Y. Sun, S. Zheng, T. Bell, and J. Smith: Indenter tip radius and load frame compliance calibration using nanoindentation loading curves. Philos. Mag. Lett. 79, 649 (1999).
29. B. Taljat and G.M. Pharr: Development of pile-up during spherical indentation of elastic-plastic solids. Int. J. Solids Struct. 41, 3891 (2004).
30. A. Bolshakov and G.M. Pharr: Influences of pileup on the measurement of mechanical properties by load and depth-sensing indentation techniques. J. Mater. Res. 13, 1049 (1998).
31. Y.T. Cheng and C.M. Cheng: Effects of "sinking in" and "piling up" on estimating the contact area under load in indentation. Philos. Mag. Lett. 78, 115 (1998).
32. Y.T. Cheng and C.M. Cheng: Relationships between hardness, elastic modulus, and the work of indentation. Appl. Phys. Lett. 73, 614 (1998).
33. W.C. Oliver and G.M. Pharr: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J. Mater. Res. 19, 3 (2004).