Axial piston pump grooved slipper analysis by CFD simulation of three-dimensional NVS equation in cylindrical coordinates

Computers and Fluids

Volumn 38, Issue 3, 2009, Pages 648-663

  Kumar, S ^a   Bergada, J M ^a   Watton, J ^b  

^a UNIVERSITAT POLITÈCNICA DE CATALUNYA   (Spain)

^b CARDIFF UNIVERSITY   (United Kingdom)

Author keywords

[No Author keywords available]

Indexed keywords

PUMPS; RECIPROCATING PUMPS; THREE DIMENSIONAL;

AXIAL PISTONS; CFD SIMULATIONS; CYLINDRICAL COORDINATES; DESIGN INSTRUCTIONS; FLUID MOMENTUMS; NAVIER STOKES; PISTON PUMPS; STATIC AND DYNAMICS; TANGENTIAL VELOCITIES; TEST RIGS; WORKING CONDITIONS;

NAVIER STOKES EQUATIONS;

EID: 57749185853     PISSN: 00457930     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.compfluid.2008.06.007     Document Type: Article

References (40)

1. Fisher MJ. A theoretical determination of some characteristics of a tilted hydrostatic slipper bearing. British Hydromechanics Research Association, 1962. Rep. RR 728.
2. Böinghoff O. Untersuchen zum Reibungsverhalten der Gleitschuhe in Schrägscheiben-Axialkolbenmascinen. VDI-Forschungsheft 584 (1977) 1-46
3. Hooke CJ, Kakoullis YP. The lubrication of slippers on axial piston pumps. In: Fifth international fluid power symposium, Durham, England, September 1978, vol. B2. p. 13-26.
4. Iboshi N., and Yamaguchi A. Characteristics of a slipper bearing for swash plate type axial piston pumps and motors, theoretical analysis. Bull JSME 25 210 (1982) 1921-1930
5. Iboshi N., and Yamaguchi A. Characteristics of a slipper bearing for swash plate type axial piston pumps and motors, experimental. Bull JSME 26 219 (1983) 1583-1589
6. Hooke C.J., and Kakoullis Y.P. The effects of non-flatness on the performance of slippers in axial piston pumps. Proc Inst Mech Eng 197C (1983) 239-247
7. Hooke C.J., and Li K.Y. The lubrication of overclamped slippers in axial piston pumps centrally loaded behaviour. Proc Inst Mech Eng 202 C4 (1988) 287-293
8. Hooke C.J., and Li K.Y. The lubrication of slippers in axial piston pumps and motors. The effect of tilting couples. Proc Inst Mech Eng 203 Part C (1989) 343-350
9. Takahashi K, Ishizawa S. Viscous flow between parallel disks with time varying gap width and central fluid source. In: JHPS international symposium on fluid power, Tokyo, March 1989. p. 407-14.
10. Koc E., and Hooke C.J. Investigation into the effects of orifice size, offset and overclamp ratio on the lubrication of slipper bearings. Tribol Int 29 4 (1996) 299-305
11. Koc E., and Hooke C.J. Considerations in the design of partially hydrostatic slipper bearings. Tribol Int 30 11 (1997) 815-823
12. Tsuta T., Iwamoto T., and Umeda T. Combined dynamic response analysis of a piston-slipper system and lubricants in hydraulic piston pump. Emerging Technologies in Fluids, Structures and Fluid/Structure Interactions. ASME 396 (1999) 187-194
13. Crabtree A.B., Manring N.D., and Johnson R.E. Pressure measurements for translating hydrostatic trust bearings. Int J Fluid Power 6 3 (2005)
14. Kazama T. Numerical simulation of a slipper model for water hydraulic pumps/motors in mixed lubrication. In: Proceedings of the sixth JFPS international symposium on fluid power, TSUKUBA, November 2005. p. 7-10.
15. Li K.Y., and Hooke C.J. A note on the lubrication of composite slippers in water based axial piston pumps and motors. Wear 147 (1991) 431-437
16. Hooke CJ, Kakoullis YP. The effects of centrifugal load and ball friction on the lubrication of slippers in axial piston pumps. In: Sixth international fluid power symposium, Cambridge, England 1981. p. 179-91.
17. Koc E., Hooke C.J., and Li K.Y. Slipper balance in axial piston pumps and motors. Trans ASME - J Tribol 114 (1992) 766-772
18. Kobayashi S, Hirose M, Hatsue J, Ikeya M. Friction characteristics of a ball joint in the swashplate type axial piston motor. In: Proceedings of the eighth international symposium on fluid power, Birmingham, England, 1988, vol. J2. p. 565-92.
19. Harris RM, Edge KA, Tilley DG. Predicting the behaviour of slipper pads in swashplate-type axial piston pumps. In: ASME winter annual meeting, New Orleans, Louisiana, 1993. p. 1-9.
20. Wieczoreck U, Ivantysynova M. CASPAR-A computer aided design tool for axial piston machines. In: Proceedings of the power transmission motion and control international workshop, Bath, UK, 2000, p. 113-26.
21. Wieczoreck U., and Ivantysynova M. Computer aided optimization of bearing and sealing gaps in hydrostatic machines-the simulation tool CASPAR. Int J Fluid Power 1 3 (2002) 7-20
22. Kakoulis YP. Slipper lubrication in axial piston pumps. M.Sc. Thesis, University of Birmingham, 1977.
23. Bergada JM, Watton J. A direct leakage flow rate calculation method for axial pump grooved pistons and slippers, and its evaluation for a 5/95 fluid application. In: Fifth JFPS international symposium on fluid power, Nara Japan, November 13, 2002.
24. Bergada JM, Watton J. Axial piston pump slipper balance with multiple lands. In: ASME international mechanical engineering congress and exposition, New Orleans, Louisiana, November 2002, vol. 2(39338).
25. Bergada J.M., Haynes J.M., and Watton J. Leakage and groove pressure of an axial piston pump slipper with multiple lands. Tribol T 5 4 (2008) 469-482
26. Johnson R.E., and Manring N.D. Translating circular thrust bearings. J Fluid Mech 530 (2005) 197-212
27. Patankar S.V. Numerical heat transfer and fluid flow (1980), Taylor & Francis Group: Hemisphere Publishing Corporation
28. Estrada C.A., Alvarez G., and Hinojosa J.F. Three-dimensional numerical simulation of the natural convection in an open tilted cubic cavity. Revista Mexicana De Fisica 52 2 (2005) 111-119
29. Zeng M., and Tao W.Q. A comparison study of the convergence characteristics and robustness for four variants of SIMPLE-family at fine grid. Eng Comput 20 3 (2003) 320-340
30. Shi X., and Khodadadi J.M. Laminar fluid flow and heat transfer in a lid driven cavity due to thin film. J Heat Transf - ASME 124 (2002) 1056-1063
31. Chen C.L., and Cheng C.H. Numerical study of flow and thermal behaviour of lid-driven flow in cavities of small aspect ratio. Int J Numer Meth Fluids 52 (2006) 785-799
32. Yao H., Cooper R.K., and Raghunathan S. Numerical simulation incompressible laminar flow over three dimensional rectangular cavities. J Fluid Eng 126 (2004) 919-927
33. Ching T.P., Hwang R.R., and Sheu W.H. On end-wall corner vortices in a lid-driven cavity. ASME - J Fluid Eng 119 (1997) 201-204
34. Iwatsu R., Hyun J.M., and Kuwahara K. Numerical simulation of three dimensional flow in a cubic cavity with an oscillating lid. ASME - J Fluid Eng 115 (1993) 680-686
35. Tasnim S.H., Mahmud S., and Das P.K. Effect of aspect ratio and eccentricity on heat transfer from a cylinder in a cavity. Int J Numer Meth Heat Fluid Flow 12 7 (2002) 855-869
36. Luan Z., and Khonsari M.M. Numerical simulation of the flow field around the ring of mechanical seals. J Tribol - ASME 128 (2006) 559-565
37. Molki M, Faghri M. Interaction between a buoyancy-driven flow and an array of annular cavities. In: Sadhana academy proceedings in engineering science, vol. 19, 1999. p. 705-21.
38. Harlow F.H., and Welch J.E. Numerical calculation of time-dependent viscous incompressible flow of fluid with free surface. Phys Fluids 8 12 (1965) 2182
39. Anderson J.D. Computational fluid dynamics. The basic with applications (1995), McGraw-Hill, Inc.
40. Bergada JM, Kumar S, Watton J. Towards an analytical solution for axial piston pump leakage and output flow ripple. In: Ninth international symposium on fluid control, measurement and visualization, FLUCOME 2007, Tallahassee, Florida, USA, 16-19 September, 2007, p. 35.