Considerations in the design of partially hydrostatic slipper bearings

Tribology International

Volumn 30, Issue 11, 1997, Pages 815-823

  Koc E ^a   Hooke, C J ^b  

^a CUKUROVA UNIVERSITY   (Turkey)

^b UNIVERSITY OF BIRMINGHAM   (United Kingdom)

Author keywords

Axial piston pumps; Partially hydrostatic; Slipper bearings

Indexed keywords

DESIGN; FILMS; LUBRICANTS; PRESSURE DROP; PUMPS; THICKNESS MEASUREMENT;

SLIPPER BEARINGS;

HYDROSTATIC BEARINGS;

EID: 0031272685     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0301-679X(97)00064-9     Document Type: Article

References (18)

1. Koç, E. and Hooke, C. J., End lubrication and sealing in gear pumps with fixed and plates. Journal of Fluid Control, 1988, 18(3), 52-69.
2. Koç, E., Analytical and experimental investigation into the sealing and lubrication mechanism of the gear ends in pumps. Wear, 1989, 135, 79-94.
3. Koç, E. and Hooke, C. J., The surface non-flatness effect on the design of bush type bearings in high pressure pumps and motors. Wear, 1989, 135, 29-39.
4. Hooke, C. J., Foster, K. and Madera, G., A note on the effect of shaft and casing stiffness on the port-plate lubrication film of a particular slipper-pad axial piston pump. Paper presented at the 4th International Fluid Power Symposium, BHRA, April 1975.
5. Turnbull, D. E. and Shute, N. A., A preliminary investigation of the characteristics of hydrostatic slipper bearings. British Hydromechanics Research Association, Report RR610, December 1958.
6. Bennett, T. P., The resistance to tilt of hydrostatic slipper pads. British Hydromechanics Research Association, Report RR669, September 1961.
7. Fisher, M. J., A theoretical determination of some characteristics of a tilted hydrostatic slipper pad. British Hydromechanics Research Association, Report RR728, April 1962.
8. Shute, N. A. and Turnbull, D. E., The minimum power loss of hydrostatic slipper bearings. British Hydromechanics Research Association, Report SP721, December 1962.
9. Shute, N. A. and Turnbull, D. E., The losses of hydrostatic bearings under various operating conditions. British Hydromechanics Research Association, Report RR743, October 1962.
10. Shute, N. A. and Turnbull, D. E., The axial and tilting stiffness of hydrostatic slipper bearings. British Hydromechanics Research Association, Report RR759, March 1963.
11. Cunningham, S. U. and McGillavary, D., The design and operation of hydrostatic slipper-pad bearings in hydrostatic motors. In Proceedings of the Institution of Mechanical Engineers, Vol. 180, Pt 3L, 1966.
12. Hooke, C. J. and Kakoullis, Y. P., The effects of non-flatness on the performance of slippers in axial piston pumps. In Proceedings of the Institution of Mechanical Engineers, Vol. 197C, 1983, pp. 239-247.
13. Hooke, C. J. and Li, K. Y., The lubrication of overclamped slippers in axial piston pumps - centrally loaded behaviour. In Proceedings of the Institution of Mechanical Engineers, Vol. 202C, 1988, pp. 287-293.
14. Koç, E., Hooke, C. J. and Li, K. Y., Slipper balance in axial piston pumps and motors. Trans. ASME, Journal of Tribology, 1992, 114, 766-772.
15. Hooke, C. J. and Kakoullis, Y. P., The effects of centrifugal load and ball friction on the lubrication of slippers in axial piston pumps. In Proceedings of the 6th International Symposium on Fluid Power, Cambridge, D2, BHRA, 1981, pp. 179-191.
16. Raimondi, A. A. and Boyd, J. A., A solution for the finite journal bearing and its application to analysis and design III. Trans. ASLE, 1958, 1, 195-209.
17. Koç, E. and Hooke, C. J., Investigation into the effects of orifice size, offset and overclamp ratio on the lubrication of slipper bearings. Tribology International, 1996, 29(4), 299-305.
18. Hooke, C. J. and Kakoullis, Y. P., On-line measurement of film thickness. In Proceedings of the Conference on Instruments and Computers for Cost Effective Fluid Power Testing. Institution of Mechanical Engineers, Paper C128/79, 1979, pp. 51-59.