Contact pressure of indented wide elliptical contacts: Dry and lubricated cases

Journal of Tribology

Volumn 130, Issue 4, 2008, Pages

  Biboulet, N ^a,b   Lubrecht, A A ^a   Houpert, L ^b  

^a UNIVERSITÉ DE LYON   (France)

^b TIMKEN Europe   (France)

Author keywords

Contamination; Fatigue; Indentation; Pollution; Rolling bearing life

Indexed keywords

BEARINGS (MACHINE PARTS); NUMERICAL ANALYSIS; STRESS CONCENTRATION;

CONTACT PRESSURES; DRY CONTACTS; ELLIPTICAL CONTACTS; FAILURE RISKS; FATIGUE; LUBRICATED CONTACTS; NUMERICAL STUDIES; PRESSURE PERTURBATIONS; PURE ROLLINGS; ROLLING BEARING LIFE; ROLLING ELEMENT BEARINGS; STRESS DISTRIBUTIONS;

BEARINGS (STRUCTURAL);

EID: 57149131820     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2960496     Document Type: Article

References (30)

1. Ko, C. N., and Ioannides, E., 1988, "Debris Denting - The Associated Residual Stresses and Their Effect on the Fatigue Life of Rolling Bearing: An FEM Analysis," Proceedings of the 14th 1988 Leeds-Lyon Symposium on Tribology, pp. 199-207.
2. Xu, G., Sadeghi, F., and Hoeprich, M. R., 1997, "Residual Stresses Due to Debris Effects in EHL Contacts," STLE Tribol. Trans., 40, pp. 613-620.
3. Jacq, C., 2001, "Limite d'Endurance et Durée de Vie en Fatigue de Roulement du 32CrMoV13 Nitruré en Présence d'Indentations," Ph.D. thesis, INSA-LYON, Lyon, France.
4. Dwyer-Joyce, R. S., 1992, "The Effect of Lubricant Contamination on Rolling Bearing Performance," Ph.D. thesis, University of London, London, England.
5. Ville, F., 1999, "Pollution Solide des Lubrifiants, Indentations et Fatigue des Surfaces," Ph.D. thesis, INSA-LYON, Lyon, France.
6. Ville, F., and Nelias, D., 1999, "An Experimental Study on the Concentration and Shape of Dents Caused by Spherical Metallic Particles in EHL Contacts," STLE Tribol. Trans., 42, pp. 231-240.
7. Ai, X., 2001, "Effect of Debris Contamination on the Fatigue Life of Roller Bearings," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 215, pp. 563-575.
8. Venner, C. H., and Lubrecht, A. A., 2000, Multilevel Methods in Lubrication (Elsevier Tribology Series), Elsevier, Amsterdam.
9. Hooke, C. J., and Li, K. Y., 2006, "Rapid Calculation of the Pressures and Clearances in Rough, Elastohydrodynamically Lubricated Contacts Under Pure Rolling. Part 1: Low Amplitude, Sinusoidal Roughness," Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci., 220, pp. 901-913.
10. Hooke, C. J., and Venner, C. H., 2006, "Rapid Calculation of the Pressures and Clearances in Rough, Elastohydrodynamically Lubricated Contacts Under Pure Rolling. Part 1: General Roughness," Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci., 220, pp. 915-925.
11. Wedeven, L. D., 1977, "Influence of Debris on EHD Lubrication," ASLE Trans., 21, pp. 41-52.
12. Wedeven, L. D., and Cusano, C., 1979, "Elastohydrodynamic Film Thickness Measurements of Artificially Produced Surface Dents and Groove," ASLE Trans., 22, pp. 369-381.
13. Coulon, S., Jubault, I., Lubrecht, A. A., Ville, F., and Vergne, P., 2004, "Pressure Profiles Measured Within Lubricated Contact in Presence of Dented Surfaces, Comparison With Numerical Models," Tribol. Int., 37, pp. 111- 117.
14. Lubrecht, A. A., and Ioannides, E., 1992, "Analysis of the Influence of Indentations on Contact Life," Proceedings of the 18th Leeds-Lyon Symposium on Tribology, pp. 173-181.
15. Ai, X., and Cheng, H. S., 1994, "The Influence of Moving Dent on Point EHL Contacts," STLE Tribol. Trans., 37, pp. 323-335.
16. Ai, X., and Lee, S. C., 1996, "Effect of Slide-to-Roll Ratio on Interior Stresses Around a Dent in EHL Contacts," STLE Tribol. Trans., 39, pp. 881-889.
17. Ai, X., and Nixon, H. R, 2000, "Fatigue Life Reduction of Roller Bearings Due to Debris Denting: Part I - Theoretical Modeling," STLE Thbol. Trans., 43, pp. 197-204.
18. Ai, X., and Nixon, H. P., 2000, "Fatigue Life Reduction of Roller Bearings Due to Debris Denting: Part II-Experimental Validation," STLE Tribol. Trans., 43, pp. 311-317.
19. Coulon, S., 2001, "Prédiction de la Durée de Vie des Contacts Ponctuels Lubrifiés en Présence d'Indentations," Ph.D. thesis, INSA-LYON, Lyon, France.
20. Coulon, S., Ville, E, and Lubrecht, A. A., 2002, "An Abacus for Predicting the Rolling Contact Fatigue Life Reduction Due to Debris Dents," Proceedings of the 28th Leeds-Lyon Symposium on Tribology, Vol. 40, pp. 283-294.
21. Coulon, S., Ville, F., and Lubrecht, A. A., 2002, "Effect of a Dent on the Pressure Distribution in Dry Point Contact Model," ASME J. Tribol., 124, pp. 220-222.
22. Hamrock, B. J., and Brewe, D., 1983, "Simplified Solution for Stresses and Deformations," ASME J. Lubr. Technol., 105, pp. 171-177.
23. Moes, H., 2000, "Lubrication and Beyond," University of Twente, Technical report.
24. Nelias, D., 2005, "New Methodology to Evaluate the Rolling Contact Fatigue Performance of Bearing Steels With Surface Dents: Application to 32Cr-MoV13 (Nitrided) and M50 Steels," ASME J. Tribol., 127, pp. 611-622.
25. Johnson, K. L., 1989, Contact Mechanics, Cambridge University Press, Cambridge, UK.
26. Roelands, C. J. A., 1966, "Correlation Aspects of the Viscosity-Temperature-Pressure Relationship of Lubricating Oils," Ph.D. thesis, Technical University Delft, Delft, The Netherlands.
27. Dowson, D., and Higginson, G. R., 1966, Elastohydrodynamic Lubrication: The Fundamentals of Roller and Gear Lubrication, Pergamon, Oxford, UK.
28. Greenwood, J. A., and Morales-Espejel, G. E., 1997, "The Behaviour of Transverse Roughness in EHL Contacts," Proceedings of the 23th Leeds-Lyon Symposium on Tribology, pp. 307-312.
29. Venner, C. H., and Lubrecht, A. A., 1999, "Amplitude Reduction of Non-Isotropic Harmonic Patterns in Circular EHL Contacts Under Pure Rolling," Proceedings of the 25th Leeds-Lyon Symposium on Tribology, pp. 151-162.
30. Hooke, C. J., and Venner, C. H., 2000, "Surface Roughness Attenuation in Line and Point Contacts," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 214, pp. 439-444.