On elastic deformation, inter-asperity cavitation and lubricant thermal effects on flow factors

Tribology International

Volumn 42, Issue 2, 2009, Pages 260-274

  Meng, F M ^a   Cen, S Q ^b   Hu, Y Z ^c   Wang, H ^c  

^a CHONGQING UNIVERSITY   (China)

^b ZHENGZHOU UNIVERSITY   (China)

^c TSINGHUA UNIVERSITY   (China)

Author keywords

Elastic deformation; Flow factors; Inter asperity cavitation; Thermal effect

Indexed keywords

CANTILEVER BEAMS; CAVITATION; DEFORMATION; ELASTIC DEFORMATION; HYDRODYNAMICS; LUBRICANTS; THERMAL EFFECTS; THERMOGRAPHY (TEMPERATURE MEASUREMENT);

COMBINED EFFECTS; EXTENDED REYNOLDS EQUATIONS; FLOW FACTORS; INFLUENCING FACTORS; INTER-ASPERITY CAVITATION; LUBRICATION CONDITIONS; NUMERICAL RESULTS; ON FLOWS; ROUGH SURFACES; SEPARATE EFFECTS; VARIATIONS OF;

LUBRICATION;

EID: 56249108365     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.triboint.2008.06.009     Document Type: Article

References (20)

1. Patir N., and Cheng H.S. An average flow model for determining effects of three-dimensional roughness partial hydrodynamic lubrication. J Lubr Technol Trans ASME 100 (1979) 12-17
2. Patir N., and Cheng H.S. Application of average flow model to lubrication between rough sliding surfaces. J Lubr Technol Trans ASME 101 (1979) 220-230
3. Lunde L., and Tønder K. Numerical simulation of the effect of three-dimensional roughness on hydrodynamic lubrication: correlation coefficients. J Tribol Trans ASME 119 2 (1997) 315-322
4. Lunde L., and Tønder K. Pressure and shear flow in a rough hydrodynamic bearing flow factor calculation. J Tribol Trans ASME 119 3 (1997) 549-555
5. Peeken H.J., Knoll G., Rienäcker A., Lang J., and Schönen R. On the numerical determination of flow factors. J Tribol Trans ASME 119 2 (1997) 259-264
6. Knoll G., Rienäcker A., Lagemann V., and Lechtape-Grüter R. Effect of contact deformation on flow factors. J Tribol Trans ASME 120 1 (1998) 140-142
7. Wilson W.R.D., and Marsault N. Partial hydrodynamic lubrication with large fractional contact areas. J Tribol Trans ASME 120 1 (1998) 16-20
8. Letalleur N., Plouraboue F., and Prat M. Average flow model of rough surface lubrication: flow factors for sinusoidal surfaces. J Tribol Trans ASME 124 3 (2002) 539-546
9. Sahlin F., Almqvist A., Larsson R., and Glavatskih S. Rough surface flow factors in full film lubrication based on a homogenization technique. Tribol Int 40 7 (2007) 1025-1034
10. Tripp J.H. Surface roughness effects in hydrodynamic lubrication: the flow factor method. J Lubr Technol Trans ASME 105 3 (1983) 458-465
11. HU Y.Z., and Zheng L.Q. Some aspects of determining the flow factors. J Tribol Trans ASME 111 3 (1989) 525-531
12. Jeng Y.R., and Tsai H.J. Grain-flow lubrication of finite-width slider bearings with rough surfaces. Tribol Lett 13 4 (2002) 219-232
13. Harp S.R., and Salant R.F. An average flow model of rough surface lubrication with inter-asperity cavitation. J Tribol 123 1 (2001) 134-143
14. Meng F.M., Wang W.Z., Hu Y.Z., and Wang H. Numerical analysis of combined influences of inter-asperity cavitation and elastic deformation on flow factors. Proc Inst Mech Eng Part C: J Mech Eng Sci 221 7 (2007) 815-827
15. Jakobsson B, Floberg L. The finite journal bearing considering vaporization. Report no. 190, Trans Chalmers University Tech, Goteborg, Sweden, 1957.
16. Olsson K. Cavitation in dynamically loaded bearings. Trans Chalmers University Tech, Report no. 308, Goteborg, Sweden, 1965.
17. Payvar P., and Salant R.F. A computational method for cavitation in a wavy mechanical seal. J Tribol Trans ASME 114 1 (1992) 119-204
18. Salant R.F. Numerical analysis of the flow field within lip seals containing micro undulations. J Tribol Trans ASME 114 3 (1992) 485-492
19. Liu Y.C., Wang Q.J., Wang W.Z., Hu Y.Z., and Zhu D. Effects of differential scheme and mesh density on EHL film thickness in point contacts. J Tribol Trans ASME 128 3 (2006) 641-653
20. Yang P.R., and Rodkiewiczt C.M. Time-dependent TEHL solution to certainly supported tilting pad bearings subjected to harmonic vibration. Tribol Int 29 5 (1996) 433-443