Refining mechanisms and development of TMP properties in a low-consistency refiner

International Mechanical Pulping Conference 2007, TAPPI

Volumn 1, Issue , 2007, Pages 62-75

  Eriksen, Oddbjørn ^a   Hammar, Lars Åke ^b  

^a Papir og fiberinstituttet AS   (Norway)

^b INNVENTIA AB   (Sweden)

Author keywords

[No Author keywords available]

Indexed keywords

CONTROL MECHANISMS; DESIGN AND CONTROLS; EXPERIMENTAL RESEARCHES; LC REFINING; LOWER ENERGIES; NORWAY SPRUCES; ONE PASSES; OPERATING WINDOWS; PICEA ABIES; PROCESS OPERATIONS; PULP QUALITIES; REFINING MECHANISMS; TENSILE INDICES; TOTAL ENERGY CONSUMPTIONS; TREATMENT PROCESSES;

FIBERS; GALLIUM ALLOYS; MACHINE DESIGN; MECHANICAL PROPERTIES; MECHANICAL PULP; MECHANISMS; PRESSURE MEASUREMENT; PROCESS CONTROL; PROCESS ENGINEERING; PULP; REFINING; THERMOMECHANICAL PULPING PROCESS;

PULP REFINING;

FIBERS; GALLIUM; MECHANICAL PROPERTIES; MECHANICAL PULPS; PRESSURE MEASUREMENT; PROCESS CONTROL; PULPS; REFINING; THERMOMECHANICAL PULPING;

EID: 55949117022     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (27)

1. Flowers, A.G., Pearson, A.J. and Tyler, A.G. (1979): A preliminary report on single stage TMP pulping of P.radiata followed by post refining, Appita 33(3): 195-200.
2. Musselmann, R., Letarte, D. and Simard, R. (1997): Third stage low consistency refining of TMP for energy savings and quality enhancement, 4th International Refining Conference, Pira, pp. 141-147.
3. Hammar, L.-ÅR., Htun, M. and Svensson, B. (1997): A two-stage refining process to save energy for mechanical pulps, International mechanical pulping conference, pp. 257-262.
4. Page, D.H. (1989): The beating of chemical pulps - the action and the effects, 9th Fundamental Research Symposium, "Fundamentals of Papermaking", pp. 1-38.
5. Ebeling, K. (1981): A critical review of current theories for the refining of chemical pulps, Institute of Paper Chemistry, Appelton, WI, Report 3 (Project 3384), 69 p.
6. Fahey, M. D. (1970): Mechanical treatment of chemical pulps, Tappi 53(11):2050-2064.
7. Nordman, L., Levlin, J.-E., Markonen, T. and Jokisalo, H. (1981): Conditions in an LC-refiner as observed by physical measurements, Pap. Puu 63 (4):169-180.
8. Stationwala, M.I., Atack, D., Wood, J.R., Wild, D.J. and Karnis, A. (1979): The effect of control variables on refining zone conditions and pulp properties, International Mechanical Pulping Conference, pp. 93-109.
9. Dahlqvist, G. and Ferrari, B. (1981): Mill operating experience with a TMP refiner control system based on a true disc clearance measurement, International Mechanical Pulping Conference, pp. 1-14.
10. Jackson, M., Falk, B. and Danielsson, O. (1986): Refining systems, pulp quality can be tailored to specific enduse needs, Pulp and Paper, 60 (6):60-63.
11. Mohlin, U.-B. (2006a): LC-refining of chemical pulps - refining intensity and gap clearance, Industrikontakt, STFI-Packforsk, Stockholm, Sweden, No. 1, pp. 9-11.
12. Mohlin, U.-B. (2006b): Refining intensity and gap clearance, 9th International Refining Conference, Pira.
13. Khlebnikov, A.A., Pashinskii, V.F., Goncharov, V.N. and Smirnova, E.A. (1969): Analysis of forces involved in the operation of a conical refiner, Bumazh. Prom. 22:129-136, English Trans.
14. Goncharov, V.N., Smirnova, E.A. and Shemyakin, E.V. (1970): Method for the determination of stresses between refiner blades, Bumazh. Prom. (27): 134-138, English Trans.
15. Goncharov, V.N. (1971): Force factors in a disk refiner and their effect on the beating process, Bumazh. Prom., 5:12-14, English Trans.
16. Atack, D. (1977): Advances in beating and refining, Transaction of the Oxford Symposium, "Fibre-water interactions in paper-making", British paper and Board Industry Federation, pp. 261-297.
17. Eriksen, O. (2003): High-frequency pressure measurements in the refining zone of a high-consistency refiner, Doctoral thesis, Norwegian University of Science and Technology, ISBN: 82-471-5601-6, 303 p.
18. Eriksen, O., Gregersen, Ø. and Krogstad, P.-Å. (2005): Refining zone pressure in a mill-scale TMP refiner measured by fibre-optic sensors, Nord. Pulp Paper Res. J. 20(4):468-476.
19. Banks, W.A. (1967): Design considerations and engineering characteristics of disk refiners, Paper Technol. 8(4):363.
20. Eriksen, O., Gregersen, Ø. and Krogstad, P.-Å. (2006): Pressure and vibration in the refining zone of a TMP refiner-influence of the fibre flow, Nord. Pulp Paper Res. J., 21(1):90-98.
21. Page, D.H., Kosky, J. and Booth, D. (1962): Some initial observations on the action of the beater, BP&BIRA Bulletin 28:15-21.
22. Franc, J.-P. and Michel, J.-M. (2004): Fundamentals of cavitation, Kluwer Academic Publisher, Dordrecht, The Netherlands, 289 p., ISBN: 1-4020-2232-8.
23. Melby, B. A.(ed.) (1919): Ny literature. Heltøyshollænderen, Papir Journalen, 8(4):23-27.
24. Stephansen, E. (1967): Bidrag til belysning av maleprosessens mekanisme, Norsk Skogindustri, 21(8):266-275.
25. Fox, T. S., Brodkey, R. S. and Nissan, A. H. (1979): High-speed photography of stock transport in a disc refiner, Tappi 62(3):55-58.
26. Espenmiller, H.P.(1969): The theory and practice of refining, Southern Pulp & Paper Manufacturer, 32(4):50-57.
27. Steenberg, B. (1963): Review of the effect of mechanical treatment of fibres, Svensk Papperstid. 66(22):933-939.