Pressure and vibration in the refining zone of a TMP refiner - Influence of the fibre flow

Nordic Pulp and Paper Research Journal

Volumn 21, Issue 1, 2006, Pages 90-98

  Eriksen, Oddbjørn ^a   Gregersen, Øyvind ^b   Krogstad, Per Åge ^b  

^a Papir og fiberinstituttet AS   (Norway)

^b NORWEGIAN UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Norway)

Author keywords

Fibre optic sensor (EFPI); Frequency analysis (FFT); Pressure; Refining zone; Thermomechanical pulp (TMP); Twin refiner; Vibration

Indexed keywords

FABRY-PEROT INTERFEROMETERS; FIBER OPTIC SENSORS; THERMOMECHANICAL PULP;

FREQUENCY ANALYSIS (FFT); REFINING ZONE; TWIN REFINERS; VIBRATION;

PULP REFINING;

PRESSURE; REFINERS; REFINING; SENSORS; STOCK FLOW; VELOCITY; VIBRATION;

EID: 33645724489     PISSN: 02832631     EISSN: None     Source Type: Journal    
DOI: 10.3183/npprj-2006-21-01-p090-098     Document Type: Article

References (23)

1. Atack, D. and Stationwala, M.I. (1975): On the measurement of temperature and pressure in the refining zone of an open discharge refiner, Transactions of the Technical Section CPPA 1(3), 71-76.
2. Caucal, G., Chaussy, D. and Renaud, M. (1992b): Etude physique et hydraulique du raffinage III, Rev. ATIP 46(7), 194-199.
3. Caucal, G., Chaussy, D. and Renaud, M. (1992a): Etude physique et hydraulique du raffinage II, Rev, ATIP 46(5), 130-138.
4. Caucal, G., Chaussy, D. and Renaud, M. (1991): Etude physique et hydraulique du raffinage, Rev. ATIP 45(5), 187-199.
5. Eriksen, O., Gregersen, O. and Krogstad, P.-Å. (2005a): High-speed measurements of pressure and temperature in the refining zone of a high-consistency refiner, Nord. Pulp Paper Res. J. 20(4),459-467.
6. Eriksen, O., Gregersen, Ø. and Krogstad, P.-Å. (2005b): Refining zone pressure in a mill-scale TMP refiner measured by fibre-optic sensors, Nord. Pulp Paper Res. J. 20(4),468-476.
7. Eriksen, O., Gregersen, Ø. and Krogstad, P.-Å. (2005): Theoretical estimates of expected refining zone pressure in a mill-scale TMP refiner, Nord. Pulp Paper Res. J. 21(1),82-89.
8. Eriksen, O., Mosbye, K., Johansson, O., Rice, T., Boyd, C., Gregersen, Ø., Krogstad, P.-Å., Hammer, E. and Muggerud, E. (2003): Diagnosis of a first-stage mill-scale TMP refiner by means of refining zone pressure and temperature measurements and blow line pulp analysis, International Mechanical Pulping Conference proceedings, 389-401.
9. Eriksen, O. (2003): High-frequency pressure measurements in the refining zone of a high-consistency refiner, Doctoral thesis, Department of Energy and Process Technology, Norwegian University of Science and Technology, 50(04), 303 p., ISBN: 82-471-5601-6.
10. Goncharov, V.N. (1971): Force factors in a disk refiner and their effect on the beating process, Bumazh. Prom. 5, 12-14.
11. Gullichsen, J. (1989): Low frequency refining - a new way to make mechanical pulp, International Mechanical Pulping Conference proceedings, 320-342.
12. Hietanen, S. (1991): Effect of control variables and length of refining zone on the refining results with a new pilot refiner, Paperi Puu 73(1), 52-61.
13. Khlebnikov, A.A., Pashinskii, V.F., Goncharov, V.N. and Smirnova, E.A. (1969): Analysis of forces involved in the operation of a conical refiner, Bumazh. Prom. 22, 129-136.
14. Nordman, L., Levlin, J.-E., Makkonen, T. and Jokisalo, H. (1981): Conditions in an LC-refiner as observed by physical measurements, Paperi Puu 63 (4), 169-180.
15. Ohis, P-E. and Syrjänen, A. (1976): The importance of disc parallelism in single rotating disc refiners, Tappi, 59(1), 100-103.
16. Ouellet, D. and Weiss, R. (1994): Modeling of the nonlinear, axial vibrations of the rotor assembly in a disc refiner, J. Pulp Paper Sci., 20 (9), J259-J265.
17. Petrusewicz, S.A. and Longmore, D.K. (1974): Noise and vibration control for industrialists, Scientific Books Ltd., London, UK, 284 p., ISBN: 0-236-17704-4.
18. Pettersen, G.W. (1986): Noise emanation from conical refiners, Pulp Paper Can., 87(9), T336-T340.
19. Senger, J.J., Siadat, A., Ouellet, D. and Wild, P. (2004): Measurement of normal and shear forces during refining using a piezoelectric force sensor, J. Pulp Paper Sci. 30 (9), 247-251.
20. Stationwala, M.I., Atack, D., Wood, J.R., Wild, D.J. and Karnis, A. (1991): The effect of control variables on refining zone conditions and pulp properties Paperi Puu, 73 (1), 62-69.
21. Strand, B.C. and Hartler, N. (1985): Modelling and optimization of full scale chip refining, International Mechanical Pulping Conference proceedings, 46-54.
22. Strand, B.C. and Mokvist, A. (1987): Control and optimization of conical disc refiners, International Mechanical Pulping Conference proceedings, 11-18.
23. Wowk, V. (1991): Machinery vibration: measurement and analysis, McGraw-Hill Inc., New York, USA, 325 p., ISBN: 0-07-071936-5.