Influence of two-sided surface waviness on the EHL behavior of rolling/sliding point contacts under thermal and non-Newtonian conditions

Journal of Tribology

Volumn 130, Issue 4, 2008, Pages

  Yang, Peiran ^a   Cui, Jinlei ^a   Jin, Z M ^b   Dowson, D ^b  

^a QINGDAO TECHNOLOGICAL UNIVERSITY   (China)

^b UNIVERSITY OF LEEDS   (United Kingdom)

Author keywords

EHL; Non Newtonian; Surface waviness; Thermal

Indexed keywords

LUBRICANTS; LUBRICATION; NON NEWTONIAN FLOW; SURFACE TOPOGRAPHY;

AMBIENT PRESSURES; CYCLIC SOLUTIONS; EHL; ENTRAINMENT VELOCITIES; EYRING MODELS; EYRING SHEAR STRESSES; FULL NUMERICAL SOLUTIONS; HERTZIAN CONTACTS; LUBRICATING BEHAVIORS; MINOR AXIS; NON NEWTONIANS; NON-NEWTONIAN; QUASISTEADY SOLUTIONS; SINUSOIDAL FUNCTIONS; SURFACE WAVINESS; SURFACE WAVINESSES; THERMAL; TIME STEPS;

ELASTOHYDRODYNAMIC LUBRICATION;

EID: 54149113610     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2958078     Document Type: Article

References (37)

1. Chow, L. S. H., and Cheng, H. S., 1976, "Pressure Perturbation in EHD Contacts Due to an Ellipsoidal Asperity," ASME J. Lubr. Technol., 98, pp. 8-15.
2. Chang, L., Cusano, C., and Conry, T. F, 1989, "Effects of Lubricant Rheology and Kinematic Conditions on Micro-Elastohydrodynamic Lubrication," ASME J. Tribol., 111, pp. 344-351.
3. Sadeghi, F., and Sui, P. C., 1990, "Thermal Elastohydrodynamic Lubrication of Rough Surfaces," ASME J. Tribol., 112, pp. 341-346.
4. Ai, X., and Cheng, H. S., 1994, "The Influence of Moving Dent on Point EHL Contacts," STLE Tribol. Trans., 37, pp. 323-335.
5. Venner, C. H., and Lubrecht, A. A., 1994, "Fransient Analysis of Surface Features in an EHL Line Contact in the Case of Sliding," ASME J. Tribol., 116, pp. 186-193.
6. Yang, P., and Shen, J., 1996, "On the Theory of Time-Dependent Micro-TEHL for a Non-Newtonian Lubricant in Line Contacts," Lubr. Sci., 8, pp. 297-312.
7. Evans, H. P., and Snidle, R. W., 1996, "A Model for Elastohydrodynamic Film Failure in Contacts Between Surfaces Having Transverse Finish," ASME J. Tribol., 118, pp. 847-857.
8. Zhu, D., and Ai, X., 1997, "Point Contact EHL Based on Optically Measured Three-Dimensional Rough Surfaces," ASME J. Tribol., 119, pp. 375-384.
9. Jiang, X., Hua, D. Y., Cheng, H. S., Ai, X., and Lee, S. C., 1999, "A Mixed Elastohydrodynamic Lubrication Model With Asperity Contact," ASME J. Tribol., 121, pp. 481-491.
10. Venner, C. H., Berger, G., and Lugt, P. M., 2004, "Waviness Deformation in Starved EHL Circular Contacts," ASME J. Tribol., 126, pp. 248-257.
11. Yang, P., Cui, J., Kaneta, M., and Nishikawa, H., 2004, "Influence of a Surface Bump or Groove on the Lubricating Performance and Dimple Phenomena in Simple Sliding Point EHL Contacts," ASME J. Tribol., 126, pp. 466-472.
12. Jackson, A., and Cameron, A., 1976, "An Interferometric Study of the EHL of Rough Surfaces," ASLE Trans., 19, pp. 50-60.
13. Wedeven, L. D., and Cusano, C., 1979, "Elastohydrodynamic Film Thickness Measurements of Artificially Produced Surface Dents and Grooves," ASLE Trans., 22, pp. 369-381.
14. Kaneta, M., and Cameron, A., 1980, "Effects of Asperities in Elastohydrodynamic Lubrication," ASME J. Lubr. Technol., 102, pp. 374-379.
15. Cusano, C., and Wedeven, L. D., 1982, "The Effects of Artificially Produced Defects on the Film Thickness Distribution in Sliding EHD Point Contacts," ASME J. Lubr. Technol., 104, pp. 365-375.
16. Kaneta, M., Sakai, T., and Nishikawa, H., 1992, "Optical Interferometric Observations of the Effects of a Bump on Point Contact EHL," ASME J. Tribol., 114, pp. 779-784.
17. Kaneta, M., and Nishikawa, H., 1994, "Local Reduction in Thickness of Point Contact EHL Films Caused by a Transversely Oriented Moving Groove and Its Recovery," ASME J. Tribol., 116, pp. 635-639.
18. Zhu, D., and Wen, S., 1984, "A Full Numerical Solution of the Thermal Elastohydrodynamic Lubrication Problem of Elliptic Contact," ASME J. Tribol., 106, pp. 246-254.
19. Kim, K. H., and Sadeghi, F., 1992, "Three-Dimensional Temperature Distribution in EHD Lubrication: Part I - Circular Contact," ASME J. Tribol., 114, pp. 32-41.
20. Kim, K. H., and Sadeghi, F., 1993, "fbree-Dimensional Temperature Distribution in EHD Lubrication: Part II - Point Contact and Numerical Formulation," ASME J. Tribol., 115, pp. 36-45.
21. Qu, S., Yang, P., and Guo, F., 2000, "Theoretical Investigation on the Dimple Occurrence in the Thermal EHL of Simple Sliding Steel-Glass Circular Contacts," Tribol. Int., 33, pp. 59-65.
22. Yang, P., Qu, S., Kaneta, M., and Nishikawa, H., 2001, "Formation of Steady Dimples in Point TEHL Contacts," ASME J. Tribol., 123, pp. 42-49.
23. Guo, F., Yang, P., and Qu, S., 2001, "On the Theory of Thermal Elastohydrodynamic Lubrication at High Slide-Roll Ratios - Circular Glass-Steel Contact Solution at Opposite Sliding," ASME J. Tribol., 123, pp. 816-821.
24. Kim, H. J., Ehret, P., Dowson, D., and Taylor, C. M., 2001, "Thermal Elastohydrodynamic Analysis of Circular Contacts, Part 1: Newtonian Model," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 215, pp. 339-352.
25. Kim, H. J., Ehret, P., Dowson, D., and Taylor, C. M., 2001, "Thermal Elastohydrodynamic Analysis of Circular Contacts, Part 2: Non-Newtonian Model," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 215, pp. 353-362.
26. Liu, X., Jiang, M., Yang, P., and Kaneta, M., 2005, "Non-Newtoman Thermal Analyses of Point EHL Contacts Using the Eyring Model," ASME J. Tribol., 127, pp. 70-81.
27. Holmes, M. J. A., Evans, H. P., Hughes, T. G., and Snidle, R. W., 2003, "Transient Elastohydrodynamic Point Contact Analysis Using a New Coupled Differential Deflection Method, Part 1: Theory and Validation," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 217, pp. 289-303.
28. Holmes, M. J. A., Evans, H. P., Hughes, T. G., and Snidle, R. W., 2003, "Transient Elastohydrodynamic Point Contact Analysis Using a New Coupled Differential Deflection Method, Part 2: Results," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 217, pp. 305-321.
29. Jin, Z. M., Yang, P., Cui, J., and Dowson, D., 2004, "Transient Elastohydrodynamic Analysis of Elliptical Contacts, Part 1: Isothermal and Newtonian Lubricant Solution," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 218, pp. 211-224.
30. Yang, P., Cui, J., Jin, Z. M., and Dowson, D., 2005, "Transient Elastohydrodynamic Analysis of Elliptical Contacts, Part 2: Thermal and Newtonian Lubricant Solution," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 219, pp. 187-200.
31. Cui, J., Yang, P., Jin, Z. M., and Dowson, D., 2007, "Transient Elastohydrodynamic Analysis of Elliptical Contacts, Part 3: Non-Newtonian Lubricant Solution Under Isothermal and Thermal Conditions," Proc. Inst. Mech. Eng., Part I: J. Eng. Tribol., 221, pp. 63-73.
32. Yang, P., and Wen, S., 1990, "A Generalized Reynolds Equation for Non-Newtonian Thermal Elastohydrodynamic, Lubrication," ASME J. Tribol., 112, pp. 631-636.
33. Roelands, C. J. A., 1966, "Correlation Aspects of Viscosity-Temperature-Pressure Relationship of Lubricating Oils," Ph.D. thesis, Delft University of Technology, Netherlands.
34. Dowson, D., and Higginson, G. R., 1966, Elastohydrodynamic Lubrication, Pergamon, Oxford.
35. Venner, C. H., 1991, "Multilevel Solution of the EHL Line and Point Contact Problems," Ph.D. thesis, Twente University, Enschede, Netherlands.
36. Brandt, A., and Lubrecht, A. A., 1990, "Multilevel Matrix Multiplication and Fast Solution of Integral Equations," J. Comput. Phys., 90, pp. 348-370.
37. Yang, P., Wang, J., and Kaneta, M., 2006, "Thermal and Non-Newtonian Numerical Analyses for Starved EHL Line Contacts," ASME J. Tribol., 128, pp. 282-290.