Forces during bar-passing events in low consistency refining: Effects of refiner tram

Annual Meeting of the Pulp and Paper Technical Association of Canada (PAPTAC)

Volumn B, Issue , 2006, Pages

  Prairie, Brett ^a   Wild, Peter ^a   Byrnes, Peter ^a   Olender, D ^a   Francis, D W ^b   Ouellet, D ^b  

^a UNIVERSITY OF VICTORIA   (Canada)

^b PAPRICAN   (Canada)

Author keywords

[No Author keywords available]

Indexed keywords

PAPER AND PULP INDUSTRY; PULP REFINING; RAILROAD ROLLING STOCK;

ANNUAL MEETINGS; CONICAL REFINER; PREPRINTS; PULP AND PAPER TECHNICAL ASSOCIATION OF CANADA; SHEAR FORCE; SHEAR FORCES;

REFINING;

EID: 52349119981     PISSN: 14947722     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (14)

1. GONCHAROV, V.N., SMIRNOVA, E.A., and SHEMYAKIN, E.V., "Method for the determination of stresses between refiner blades.", Bumazh. Promst.(27): 134-138, English Trans. (1970).
2. GONCHAROV, V.N., "Force factors in a disk refiner and their effect on the beating process.", Bumazh. Promst. 12(5):12-14, English Trans., (1971).
3. NORDMAN, L., LEVLIN, J.E., MAKKONEN, T., and JOKISALO, H., "Conditions in an LC-refiner as observed by physical measurements.", Paperi ja Puu. 63(4): 169-180, (1981).
4. MARTINEZ, D.M. and KEREKES, RJ, "Forces on fibres in low consistency refining.", Tappi J. 77(12): 119-123 (1994).
5. MARTINEZ, D.M., "The energy expended on pulp fibres during low consistency refining.", Ph.D. Thesis, Department of Chemical Engineering, University of British Columbia, Vancouver, B.C. (1995).
6. MARTINEZ, D.M., BATCHELOR, W.J., KEREKES, R.J., and OUELLET, D., "Forces on fibres in low consistency refining: Normal force.", J. Pulp Paper Sci. 23(1)J11-18 (1997).
7. BATCHELOR, W.J., MARTINEZ, D.M., KEREKES, R.J., and OUELLET, D., "Forces on fibres in low consistency refining: Shear force.", J. Pulp Paper Sci. 23(1)J40-45 (1997).
8. SENGER, J.J., "The forces on pulp fibres during refining.", M.A.Sc. Thesis, Dept. of Mechanical Engineering, University of British Columbia, Vancouver, BC (1998).
9. SENGER, J.J. and OUELLET, D., "Factors affecting the shear forces in high consistency refining.", J. Pulp Paper Sci. 28(11):364-369 (2002).
10. SIADAT, A., A. BANKES, P.M. WILD, J. SENGER, AND D. OUELLET, "Development of a Piezoelectric Force Sensor for a Chip Refiner," Institution of Mechanical Engineers, Part E, Journal of Process Mechanical Engineering, Vol. 217, 133-140, (2003).
11. SENGER, J., M. OLMSTEAD, D. OUELLET AND P.M. WILD, "Measurement of Shear and Normal Forces in the Refining Zone of a TMP Refiner," Journal of Pulp and Paper Science, Vol. 30 No. 9, 247-251, (2004)
12. SENGER, J., D. OUELLET, P.M. WILD, P. BYRNES AND M. SABOURIN, "A Technique to Measure Residence Time in TMP Refiners Based on Inherent Process Fluctuations," International Mechanical Pulping Conference, Oslo, Norway, 19-25 (2005).
13. OHLS, P.E., and SYRJÄNEN, A., "Importance of disc parallelism in single disc chip refiner", Intl. Mech. Pulp. Conf., San Francisco, 153-161, (1975).
14. FRAZIER, W.C., "Refiner tram and its contribution to pulping and pulp movement in high consistency refiners", Intl. Mech. Pulp. Conf., Oslo, Norway, 38-41, (2005).