Cylindrical milling of ruled surfaces

International Journal of Advanced Manufacturing Technology

Volumn 38, Issue 7-8, 2008, Pages 649-656

  Sprott, K ^a   Ravani, B ^b  

^a CALIFORNIA STATE UNIVERSITY   (United States)

^b University of California Davis   (United States)

Author keywords

Cylindrical milling; Flank milling; Line geometry; Ruled surface

Indexed keywords

CYLINDRICAL MILLING; DIFFERENTIAL GEOMETRY; FLANK MILLING; LINE GEOMETRY; MACHINING ERRORS; PATH PLANNING; RULED SURFACE; RULED SURFACES;

MILLING (MACHINING);

EID: 49649093304     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-007-1133-6     Document Type: Article

References (19)

1. Bedi S, Mann S, Menzel C (2003) Flank milling with flat end milling cutters. Comput Aided Des 35:293-300
2. Gong H, Cao L-X, Liu J (2005) Improved positioning of cylindrical cutter for flank milling ruled surfaces. Comput Aided Des 37:1205-1213
3. Guggenheimer HW (1977) Differential geometry. Dover Publications, New York
4. Ku TS, Ravani B (1991) Bertrand offsets of ruled and developable surfaces. Comput Aided Des 23(2):145-152
5. Lartigue C, Duc E, Affouard A (2003) Tool-path deformation in 5-axis flank milling using envelope surface. Comput Aided Des 35:375-382
6. Lee J, Suh S (1998) Interference-free tool-path planning for flank milling of twisted ruled surfaces. Int J Adv Manuf Technol 14:795-805
7. Liu X-W (1995) Five-axis NC cylindrical milling of sculpted surfaces. Comput Aided Des 27:887-894
8. Marciniak K (1991) Geometric modelling for numerically controlled machining. Oxford University Press, New York
9. Menzel C, Bedi S, Mann S (2004) Triple tangent flank milling of ruled surfaces. Comput Aided Des 36:289-296
10. Peternell M, Pottmann H, Ravani B (1999) On the computational geometry of ruled surfaces. Comput Aided Des 31:17-32
11. Redonnet JM, Rubio W, Dessein G (1998) Side milling of ruled surfaces: optimum positioning of the milling cutter and calculation of interference. Int J Adv Manuf Technol 14(7):459-465
12. Rehsteiner F (1993) Collision-free five-axis milling of twisted ruled surfaces. Ann CIRP 42(1):457-461
13. Senatore J, Monies F, Redonnet J-M, Rubio W (2005) Analysis of improved positioning in five-axis ruled surface milling using envelope surface. Comput Aided Des 37:989-998
14. Struik DJ (1961) Lectures on classical differential geometry. Addison-Wesley, Reading, Mass
15. Study E (1903) Die geometrie der dynamen. Teubner, Leipzig
16. Stute G, Storr A, Sielaff W (1979) Nc programming of ruled surfaces for five-axis machining. Ann CIRP 28(1):267-271
17. Tsay DM, Her MJ (2001) Accurate 5-axis machining of twisted ruled surfaces. J Manuf Sci Eng 123:731-738
18. Veldkamp GR (1976) On the use of dual numbers, vectors and matrices in instantaneous, spatial kinematics. Mech Mach Theory 11:141-156
19. Wu C (1995) Arbitrary surface flank milling of fan, compressor, and impellerblabes. ASME J Eng Gas Turb Power 117:534-539