Forces during bar-passing events in low-consistency refining: Distributions and relationships to specific edge load

Journal of Pulp and Paper Science

Volumn 34, Issue 1, 2008, Pages 1-8

  Prairie, B ^a   Wild, P ^a   Byrnes, P ^a,d   Olender, D ^a   Francis, W ^b   Ouellet, D ^c  

^a UNIVERSITY OF VICTORIA   (Canada)

^b PAPRICAN   (Canada)

^c Novadaq Technologies Inc   (Canada)

^d NATIONAL RESEARCH COUNCIL CANADA   (Canada)

Author keywords

Bars; Coefficient of friction; Conical refiners; Edges; Loads; Low consistency; Measurement; Refining; Shear stress

Indexed keywords

FRICTION; IMAGE SEGMENTATION; SENSORS; WEIBULL DISTRIBUTION;

BARS; COEFFICIENT OF FRICTION; CONICAL REFINERS; EDGES; LOADS; LOW CONSISTENCY;

REFINING;

EID: 47549102791     PISSN: 08266220     EISSN: None     Source Type: Journal    
DOI: None     Document Type: Article

References (13)

1. SIADAT, A., BANKES, A., WILD, P.M., SENGER, J. and OUELLET, D., "Development of a Piezoelectric Force Sensor for a Chip Refiner", Inst. Mech. Engin., Part E, J. Proc. Mech. Engin. 217: 133-140 (2003).
2. SENGER, J., OLMSTEAD, M., OUELLET, D. AND WILD, P.M., "Measurement of Shear and Normal Forces in the Refining Zone of a TMP Refiner", J. Pulp Paper Sci. 30(9):247-251 (2004).
3. SENGER, J., OUELLET, D., WILD, P.M., BYRNES, P. and SABOURIN, M., "A Technique to Measure Mean Residence Time in TMP Refiners Based on Inherent Process Fluctuations", J. Pulp Paper Sci. 32(2):83-89 (2006).
4. OLENDER, D., WILD, P., BYRNES, P., OUELLET, D. and SABOURIN, M., "Forces on Bars in High-Consistency Mill-Scale Refiners: Trends in Primary and Rejects Stage Refiners", J. Pulp Paper Sci. 33(3): 163-171 (2007).
5. PRAIRIE, B., WILD, P., BYRNES, P., OLENDER, D., FRANCIS, D.W. and OUELLET, D., "Forces During Bar-Passing Events in Low Consistency Refining: Effect of Refiner Tram", Pulp Paper Can. 108(9):T153-T156 (2008).
6. KEREKES, R.J. and SENGER, J., "Characterizing Refining Action in Low Consistency Refiners by Forces on Fibres", J. Pulp Paper Sci. 32(1):1-8 (2006).
7. GIERTZ, H.W., "A New Way to Look at the Beating Process", Norsk Skog. 18(7):239-248 (1964).
8. MAYADE, T.L., "Statistical Theory of Chemical Pulp Refining - An Innovative Combined Approach", Appita J. 50(3):237-244 (1997).
9. GONCHAROV, V.N., "Force Factors in a Disk Refiner and their Effect on the Beating Process", Bumazh. Promst. 12(5):12-14, English Trans. (1971).
10. PRABHAKAR MURTHY, D.N., XIE, M. and JIANG, R., Weibull Models, Wiley-Interscience, Hoboken, NJ, USA (2003).
11. PRAIRIE, B., "Development of a Low Consistency Mechanical Force Sensor", MASc Thesis, University of Victoria, Victoria, BC, Canada (2005).
12. NORDMAN, L., LEVLIN, J., MAKKONEN, T. and JOKISALO, H., "Conditions in an LC-Refiner as Observed by Physical Measurements", Paperija Puu Volume number(4):169-180 (1981).
13. CAUCAL, G., CHAUSSY, D. and RENAUD, M., "Etude Physique et Hydraulique du Raffinage", Revue ATIP, 45(5):187-199 (1991).