Forces during bar-passing events in low consistency refining: Effects of refiner tram

Pulp and Paper Canada

Volumn 108, Issue 9, 2007, Pages 34-37

  Prairie, B ^a   Wild, P ^a   Byrnes, P ^a   Olender, D ^a   Francis, D W ^b   Quellet, D ^b  

^a UNIVERSITY OF VICTORIA   (Canada)

^b Institute of Canada   (Canada)

Author keywords

Refiners; Refining; Rotation; Rotors; Sensors; Shear Stress; Velocity

Indexed keywords

REFINERS; ROTOR ROTATION;

PIEZOELECTRIC CERAMICS; REFINING; ROTATION; ROTORS; VELOCITY MEASUREMENT;

SENSORS;

EID: 36349034747     PISSN: 03164004     EISSN: None     Source Type: Trade Journal    
DOI: None     Document Type: Article

References (14)

1. GONCHAROV, V.N., SMIRNOVA, E.A., SHEMYAKIN, E.V. Method for the determination of stresses between refiner blades. English Trans. of Bunuuh. Promst. (27):134-138(1970).
2. GONCHAROV, V.N. Force factors in a disk refiner and their effect on the beating process. English Trans. of Bumazh, Promst. 12(5):12-14 (1971).
3. NORDMAN, L., LEVLIN, J.E., MAKKONEN, T., JOKISALO, H. Conditions in an LC-refiner as observed by physical measurements. Paperi ja Puu. 63(4): 169-180 (1981).
4. MARTINEZ, D.M., KEREKES, R.J. Forces on libres in low consistency refining. Tappi J. 77(12):119-12S (1994).
5. MARTINEZ, D.M. The energy expended on pulp fibres during low consistency refining. Ph.D. Thesis, Department of Chemical Engineering, University of British Columbia, Vancouver, B.C. (1995).
6. MARTINEZ, D.M., BATCHELOR, W.J., KEREKES, R.J., OUELLET, D. Forces on fibres in low consistency refining: Normal force. J. Pulp Paper Sci. 23(1 ) J1118 (1997).
7. BATCHELOR, W.J., MARTINEZ, D.M., KEREKES, R.J., OUELLET, D. Forces on fibres in low consistency refining: Shear force. J. Pulp Paper Sci. 23 ( 1 ) : J40-45 (1997).
8. SENGER, J.J. The forces on pulp fibres during refining. M.A.Sc. Thesis, Dept. of Mechanical Engineering, University of British Columbia, Vancouver, RC (1998).
9. SENGER, J.J., OUELLET, D. Factors affecting the shear forces in high consistency refining. J. Pulp Paper Sci. 28(11):364-369 (2002).
10. SIADAT, A., BANKES, A., WILD, P.M., SENGER, J., OUELLET, D, Development of a Piezoelectric Force Sensor for a Chip Refiner. Institution of Mechanical Engineers, Part E, Journal of Process Mechanical Engineering 217(2):l'SS-140 (2003).
11. SENGER, J., OLMSTEAD, M., OUHLLET, D., WILD, P.M. Measurement of Shear and Normal Forces in the Refining Zone of a TMP Refiner, J. Pulp Paper Sci. 30(9): 247-251 (2004).
12. SENGER, J., OUELIET, D., WILD, P.M., BYRNES, P., SABOURIN, M. A Technique to Measure Residence Time in TMP Refiners Based on Inherent Process Fluctuations. Proc. International Mechanical Pulping Conference, Oslo, Norway, 19-25 (2005).
13. OHLS, P.E., SYRJÄNEN, A. Importance of disc, parallelism in single disc chip refiner. Proc. Intl. Mech. Pulp. Conf., San Francisco, 153-161 (1975).
14. FRAZIER, W.C. Refiner tram and its contribution to pulping and pulp movement in high consistency refiners. Proc. Intl. Mech. Pulp. Conf., Oslo, Norway, 38-41 (2005).