메뉴 건너뛰기




Volumn , Issue , 2003, Pages 39-48

Near-dry machining for environmentally benign manufacturing - A comparison of machining performance with flood cooling and dry machining

Author keywords

[No Author keywords available]

Indexed keywords

ALLOYS; COOLING; MICROPROCESSOR CHIPS; QUALITY CONTROL; STEEL; SURFACE CHEMISTRY; SURFACE ROUGHNESS; VARIATIONAL TECHNIQUES;

EID: 4644310255     PISSN: None     EISSN: None     Source Type: Book    
DOI: None     Document Type: Conference Paper
Times cited : (9)

References (12)
  • 1
    • 0031641373 scopus 로고    scopus 로고
    • Tool performance and chip control when machining Ti6A14V and inconel 901 using high pressure coolant supply
    • Machado, A. R., Wallbank, J., Pashby, I. R. and Ezugwu, E. O. (1998) Tool Performance and Chip Control When Machining Ti6A14V and Inconel 901 Using High Pressure Coolant Supply, Machining Science and Technology, Vol. 2/1, pp. 1-12.
    • (1998) Machining Science and Technology , vol.2 , Issue.1 , pp. 1-12
    • Machado, A.R.1    Wallbank, J.2    Pashby, I.R.3    Ezugwu, E.O.4
  • 2
    • 0033698869 scopus 로고    scopus 로고
    • Comparison methods for cutting fluid performance testing
    • Chiffre, L. De. and Belluco, W. (2000) Comparison Methods for Cutting Fluid Performance Testing, Annals of the CIRP, Vol. 49/1, pp. 57-60.
    • (2000) Annals of the CIRP , vol.49 , Issue.1 , pp. 57-60
    • Chiffre, L.De.1    Belluco, W.2
  • 3
    • 0033361630 scopus 로고    scopus 로고
    • Simultaneous measurement of the thermal and tribological effects of cutting fluid
    • Medaska, M. K., Nowag, L. and Liang, S. Y. (1999) Simultaneous Measurement of the Thermal and Tribological Effects of Cutting Fluid, Machining Science and Technology, Vol. 3/2, pp. 221-238.
    • (1999) Machining Science and Technology , vol.3 , Issue.2 , pp. 221-238
    • Medaska, M.K.1    Nowag, L.2    Liang, S.Y.3
  • 4
    • 84945867513 scopus 로고
    • Oxford Science Publication
    • Shaw, M. C. (1984) Metal Cutting Principles, Oxford Science Publication, pp. 487-543.
    • (1984) Metal Cutting Principles , pp. 487-543
    • Shaw, M.C.1
  • 6
    • 0032028535 scopus 로고    scopus 로고
    • Turning using extremely small amounts of cutting fluids
    • Wakabayashi, T., Sato, H. and Inasaki, I. (1997) Turning Using Extremely Small Amounts of Cutting Fluids, JSME International Journal, Vol. C/41(1), pp. 488-493.
    • (1997) JSME International Journal , vol.C-41 , Issue.1 , pp. 488-493
    • Wakabayashi, T.1    Sato, H.2    Inasaki, I.3
  • 7
    • 0031227415 scopus 로고    scopus 로고
    • The effect of extremely low lubricant volume in machining
    • Machado, A. R. and Wallbank, J. (1997) The Effect of Extremely Low Lubricant Volume in Machining, Wear, Vol. 210, pp. 76-82.
    • (1997) Wear , vol.210 , pp. 76-82
    • Machado, A.R.1    Wallbank, J.2
  • 9
    • 0034808199 scopus 로고    scopus 로고
    • Evaluation of minimal quantities of lubrication in end milling
    • Rahman, M., Kumar, A. S. and Manzoor-Ul-Salam, (2002) Evaluation of Minimal Quantities of Lubrication in End Milling, Int. J. Adv. Manuf. Tech., Vol. 18, pp. 235-841.
    • (2002) Int. J. Adv. Manuf. Tech. , vol.18 , pp. 235-841
    • Rahman, M.1    Kumar, A.S.2    Manzoor-Ul-Salam3
  • 11
    • 0026929754 scopus 로고
    • On the interelationships of some machinability parameters in finish turning with cermet chip forming tool inserts
    • Jawahir, I. S., Qureshi, N. and Arsacularatne, J. A. (1992) On the Interelationships of Some Machinability Parameters in Finish Turning with Cermet Chip Forming Tool Inserts, Int. J. Machine Tools and Manufacturing, Vol. 32/5, pp. 709-732.
    • (1992) Int. J. Machine Tools and Manufacturing , vol.32 , Issue.5 , pp. 709-732
    • Jawahir, I.S.1    Qureshi, N.2    Arsacularatne, J.A.3
  • 12
    • 0032679827 scopus 로고    scopus 로고
    • The effect of cutting tool thermal conductivity on tool-chip contact length and cyclic chip formation in machining with grooved tools
    • Balaji, A. K., Sreeram, G., Jawahir, I. S. and Lenz, E. (1999) The Effect of Cutting Tool Thermal Conductivity on Tool-chip Contact Length and Cyclic Chip Formation in Machining with Grooved Tools, Annals of the CIRP Vol. 48/1, pp. 33-38.
    • (1999) Annals of the CIRP , vol.48 , Issue.1 , pp. 33-38
    • Balaji, A.K.1    Sreeram, G.2    Jawahir, I.S.3    Lenz, E.4


* 이 정보는 Elsevier사의 SCOPUS DB에서 KISTI가 분석하여 추출한 것입니다.