Effects of cutting tool thermal conductivity on tool-chip contact length and cyclic chip formation in machining with grooved tools

CIRP Annals - Manufacturing Technology

Volumn 48, Issue 1, 1999, Pages 33-38

  Balaji, A K ^a   Sreeram, G ^a   Jawahir, I S ^a   Lenz, E ^b  

^a UNIVERSITY OF KENTUCKY   (United States)

^b TECHNION ISRAEL INSTITUTE OF TECHNOLOGY   (Israel)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER AIDED DESIGN; CYCLIC LOADS; HEAT TRANSFER; MACHINING; THERMAL CONDUCTIVITY; THERMOANALYSIS; THICKNESS MEASUREMENT; TRIBOLOGY;

CHIP FORMATION; FLAT FACED TOOLS; GROOVED TOOLS; TOOL CHIP CONTACT LENGTH; TOOL CHIP INTERFACE TEMPERATURE;

CARBIDE CUTTING TOOLS;

EID: 0032679827     PISSN: 00078506     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0007-8506(07)63126-6     Document Type: Article

References (17)

1. Friedman,M.Y., Lenz, E., 1971, Investigation of the Tool-Chip Contact Length in Metal Cutting, Int. Journal of Mach. Tool Des. Res., 10: 401-416.
2. Chao, B.T., Trigger, K.J., 1958, Temperature Distributions at Tool-Chip and Tool-Work Interface in Metal Cutting, Trans. ASME, 80: 311-320.
3. Klushin, M.I., 1960, Determination of the Contact Zone between Chip and Rakeface and the Pressure in this Zone, Stanki I Instrument, 31(1): 22-23.
4. Wallace, P.W., Boothroyd, G., 1964, Tool Forces and Tool-Chip Friction in Orthogonal Machining, Journal of Mech. Engg. Sci., 6(1): 74-87.
5. Rubenstein, C., 1965, A Simple Theory of Orthogonal Cutting, Int. Journal of Mach. Tool Des. Res., 4: 123-156.
6. Zorev, N.N., 1963, Inter-relationship Between Shear processes Occurring along Tool-face and Shear Plane in Metal Cutting, In: International Research in Production Engg., ASME, New York, 42-49.
7. Childs, T.H.C., Mahdi, M.I., 1989, On the Stress Distribution Between the Chip and Tool During Metal Turning, Annals of the CIRP, 38(1): 55-58
8. Gad, G.S., Armarego, E.J.A., Smith, A.J.R., 1992, Tool-Chip Contact Length in Orthogonal Machining and its Importance in Tool Temperature Predictions, Int. Journal of Production Research, 30(3): 485-501.
9. Jawahir, I.S., van Luttervelt, C.A., 1993, Recent Developments in Chip Control Research and Applications, Annals of the CIRP, 42(2): 659-693.
10. Jawahir, I.S., 1986, An Experimental and Theoretical Study of the Effects of Tool Restricted Contact on Chip Breaking, Ph.D. Thesis, University of New South Wales, Australia.
11. Spaans, C., 1970, The Fundamentals of Three- dimensional Chip Curl, Chip Breaking and Chip Control, Doctoral Dissertation, TU Delft, Netherlands.
12. Jawahir, I.S., Zhang, J.P., 1995, An Analysis of Chip Curl Development, Chip Deformation and Chip Breaking in Orthogonal Machining, Trans. NAMRI/SME, 23: 109-114.
13. Ganapathy, B.K., Jawahir, I.S., 1998, Modeling the Chip-Work Contact Force for Chip Breaking in Orthogonal Machining with a Flat-faced Tool, Journal of Manufacturing Sc. & Engg., 120(1): 49-56.
14. Fang, X.D., Jawahir, I.S., 1996, An Analytical Model for Cyclic Chip Formation in 2-D Machining with Chip Breaking, Annals of the CIRP, 45(1): 53-58.
15. Brown, C.A., 1987, Strain Analysis in Machining Using Metallographic Methods, Metallography, 20: 465-483.
16. Sullivan, K.F., Wright, P.K., Smith, P.D., 1978, Metallurgical Appraisal of Instabilities Arising in Machining, Metals Technology, June: 181-188.
17. Trent, E.M., 1988, Metal Cutting and the Tribology of Seizure: Part II - Movement of Work Material Over the Tool in Metal Cutting, Wear, 128: 47-64.