Analysis of metal workability by integration of FEM and 3-D processing maps

Journal of Materials Processing Technology

Volumn 205, Issue 1-3, 2008, Pages 497-505

  Liu, Juan ^a   Cui, Zhenshan ^a   Li, Congxin ^a  

^a SHANGHAI JIAO TONG UNIVERSITY   (China)

Author keywords

DRX; FEM; Flow instability; Power dissipation efficiency; Processing maps

Indexed keywords

DYNAMIC MODELS; DYNAMIC RECRYSTALLIZATION; ENERGY DISSIPATION; ENERGY EFFICIENCY; FINITE ELEMENT METHOD; THREE DIMENSIONAL;

DEFORMATION BEHAVIORS; DYNAMIC MATERIAL MODEL (DMM); POWER DISSIPATION EFFICIENCY; PROCESSING MAPS;

METAL WORKING;

EID: 44749086577     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2007.11.308     Document Type: Article

References (18)

1. Barnett M.R., Beer A.G., Atwell D., and Oudin A. Influence of grain size on hot working stresses and microstructures in Mg-3Al-Zn. Scripta Mater. 51 (2004) 19-24
2. Frost H.J., and Ashby M.F. Deformation Mechanism Maps (1982), Pergamon Press
3. McQueen H.J. Development of dynamic recrystallization theory. Mater. Sci. Eng. A 387-389 (2004) 203-208
4. Narayana Murty S.V.S., and Nageswarra Rao B. On the flow localization concepts in the processing maps of titanium alloy Ti-24Al-20Nb. J. Mater. Process. Technol. 104 (2000) 103-109
5. Narayana Murty S.V.S., Nageswarra Rao B., and Kashyap B.P. Instability criteria for hot deformation of materials. Int. Mater. Rev. 45 1 (2000) 15-26
6. Narayana Murty S.V.S., Nageswarra Rao B., and Kashyap B.P. Identification of flow instabilities in the processing maps of AISI 304 stainless steel. J. Mater. Process. Technol. 166 (2005) 268-278
7. Prasad Y.V.R.K. Processing maps: a status report. J. Mater. Eng. Perform. 12 (2003) 638-645
8. Prasad Y.V.R.K., and Rao K.P. Processing maps and rate controlling mechanisms of hot deformation of electrolytic tough pitch copper in the temperature range 300-950 °C. Mater. Sci. Eng. A 391 (2005) 141-150
9. Prasad Y.V.R.K., and Sasidhara S. Hot Working Guide: A Compendium of Processing Maps (1997), ASM International
10. Prasad Y.V.R.K., and Seshacharyulu T. Processing maps for hot working of titanium alloys. Mater. Sci. Eng. A 243 (1998) 82-88
11. Raj R. Development of a processing map for use in warm-forming and hot forming processes. Metall. Trans. A 12A (1989) 1089-1097
12. Semiatin S.L., and Jonas J.J. Formability and Workability of Metals: Plastic Instability and Flow Localization (1984), ASM, Metal Park, OH
13. Sivakesavam O., and Prasad Y.V.R.K. Hot deformation behaviour of as-cast Mg-2Zn-1Mn alloy in compression a study with processing map. Mater. Sci. Eng. A 362 (2003) 118-124
14. Sivaprasad P.V., Venugopal S., Davies C.H.J., et al. Identification of optimum process parameters for hot extrusion using finite element simulation and processing maps. Model. Simul. Mater. Sci. 12 (2004) 285-291
15. Tan J.C., and Tan M.J. Superplasticity in a rolled Mg-3Al-1Zn alloy by two-stage deformation method. Scripta Mater. 47 (2002) 101-106
16. Tan J.C., and Tan M.J. Superplasticity and grain boundary sliding characteristics in two stage deformation of Mg-3Al-1Zn alloy sheet. Mater. Sci. Eng. A 339 (2003) 81-89
17. Yin D.L., Zhang K.F., Wang G.F., et al. Superplasticity and cavitation in AZ31 Mg alloy at elevated temperatures. Mater. Lett. 59 (2005) 1714-1718
18. Ziegler H. An Introduction to Thermomechanics (1983), North-Holland Publishing Company, Amsterdam/New York/Oxford