Selection of optimal MQL and cutting conditions for enhancing machinability in turning of brass

Journal of Materials Processing Technology

Volumn 204, Issue 1-3, 2008, Pages 459-464

  Gaitonde, V N ^a   Karnik, S R ^a   Davim, J Paulo ^b  

^a KLE TECHNOLOGICAL UNIVERSITY   (India)

^b UNIVERSITY OF AVEIRO   (Portugal)

Author keywords

Brass; K10 carbide tool; MQL; Specific cutting force; Surface roughness; Taguchi method; Turning; Utility concept

Indexed keywords

ANALYSIS OF VARIANCE (ANOVA); BRASS; ECOLOGY; HEALTH CARE; LUBRICATION; MACHINING; SIGNAL TO NOISE RATIO;

K10 CARBIDE TOOL; SPECIFIC CUTTING FORCE; TAGUCHI METHOD; UTILITY CONCEPT;

CUTTING;

EID: 44649112059     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2007.11.193     Document Type: Article

References (14)

1. Braga D.U., Diniz A.E., Miranda G.W.A., and Coppini N.L. Using a minimum quantity of lubricant (MQL) and a diamond coated tool in the drilling of aluminum-silicon alloys. J. Mater. Process. Technol. 122 (2002) 127-138
2. Davim J.P., Sreejith P.S., Gomes R., and Peixoto C. Experimental studies on drilling of aluminium (AA1050) under dry, minimum quantity of lubricant, and flood-lubricated conditions. Proc. ImechE Part B: J. Eng. Manuf. 220 (2006) 1605-1611
3. Davim J.P., Sreejith P.S., and Silva J. Turning of brasses using minimum quantity of lubricant (MQL) and flooded-lubricant conditions. Mater. Manuf. Process. 22 (2007) 45-50
4. Dhar N.R., Islam M.W., Islam S., and Mithu M.A.H. The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel. J. Mater. Process. Technol. 171 (2006) 93-99
5. Heinemann R., Hinduja S., Barrow G., and Petuelli G. Effect of MQL on the tool life of small twist drills in deep-hole drilling. Int. J. Mach. Tool Manuf. 46 (2006) 1-6
6. Jeyapaul R., Shahabudeen P., and Krishnaiah K. Quality management research by considering multi-response problems in the Taguchi method-a review. Int. J. Adv. Manuf. Technol. 26 (2005) 1331-1337
7. Kelly J.F., and Cotterell M.G. Minimal lubrication machining of aluminium alloys. J. Mater. Process. Technol. 120 (2002) 327-334
8. Kumar P., Barua P.B., and Gaindhar J.L. Quality optimization (multi-characteristic) through Taguchi's technique and utility concept. Qual. Reliab. Eng. Int. 16 (2000) 475-485
9. Lugscheider E., Knotek O., Barimani C., Leyendecker T., Lemmer O., and Wenke R. Investigations on hard coated reamers in different lubricant free cutting operations. Surf. Coat. Technol. 90 (1997) 172-177
10. Machado A.R., and Wallbank J. The effect of extremely low lubricant volumes in machining. Wear 210 (1997) 76-82
11. Phadke M.S. Quality Engineering Using Robust Design (1989), Prentice Hall, Englewood Cliffs, NJ
12. Rahman M., Kumar A.S., and Manzoor-Ul-Salam. Evaluation of minimal quantities of lubricant in end milling. Int. J. Adv. Manuf. Technol. 18 (2001) 235-241
13. Ross P.J. Taguchi Techniques for Quality Engineering (1996), McGraw-Hill, New York
14. Sokovic M., and Mijanovic K. Ecological aspects of the cutting fluids and its influence on quantifiable parameters of the cutting processes. J. Mater. Process. Technol. 109 (2001) 181-189