Influence of processing parameters on particulate dispersion in direct laser sintered WC-Cop/Cu MMCs

International Journal of Refractory Metals and Hard Materials

Volumn 26, Issue 5, 2008, Pages 411-422

  Gu, Dongdong ^a   Shen, Yifu ^a   Xiao, Jun ^a  

^a NANJING UNIVERSITY OF AERONAUTICS AND ASTRONAUTICS   (China)

Author keywords

Direct metal laser sintering (DMLS); Metal matrix composites (MMCs); Particulate reinforcement; Rapid prototyping (RP); WC Co

Indexed keywords

AGGLOMERATION; COBALT POWDER METALLURGY; RAPID PROTOTYPING; SINTERING; WETTING;

DIRECT METAL LASER SINTERING (DMLS); METAL MATRIX COMPOSITES (MMC); PARTICULATE REINFORCEMENT; WC-CO;

METALLIC MATRIX COMPOSITES;

EID: 44449165462     PISSN: 02634368     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijrmhm.2007.09.005     Document Type: Article

References (30)

1. Velasco F., Gordo E., Isabel R., Ruiz-Navas E.M., Bautista A., and Torralba J.M. Mechanical and wear behaviour of high-speed steels reinforced with TiCN particles. Int J Refract Met Hard Mater 19 (2001) 319-323
2. Gåård A., Krakhmalev P., and Bergström J. Microstructural characterization and wear behavior of (Fe,Ni)-TiC MMC prepared by DMLS. J Alloys Compd 421 (2006) 166-171
3. 3 in submicron length scale using microwave assisted rapid sintering. Mater Sci Technol 21 (2005) 1063-1070
4. Breval E., Cheng J.P., Agrawal D.K., Gigl P., Dennis A., Roy R., et al. Comparison between microwave and conventional sintering of WC/Co composites. Mater Sci Eng A 391 (2005) 285-295
5. Gu D.D., and Shen Y.F. Effects of dispersion technique and component ratio on densification and microstructure of multi-component Cu-based metal powder in direct laser sintering. J Mater Process Technol 182 (2007) 564-573
6. Gu D.D., and Shen Y.F. Influence of phosphorus element on direct laser sintering of multicomponent Cu-based metal powder. Metall Mater Trans B 37 (2006) 967-977
7. Pintsuk G., Brünings S.E., Döring J.-E., Linke J., Smid I., and Xue L. Development of W/Cu-functionally graded materials. Fusion Eng Des 66-68 (2003) 237-240
8. Wang Y., Bergström J., and Burman C. Characterization of an iron-based laser sintered material. J Mater Process Technol 172 (2006) 77-87
9. Kruth J.P., Kumar S., and Van Vaerenbergh J. Study of laser-sinterability of ferro-based powders. Rapid Prototyping J 11 (2005) 287-292
10. 2.0. Mater Lett 59 (2005) 2812-2817
11. Gu D.D., Shen Y.F., Yang J.L., and Wang Y. Effects of processing parameters on direct laser sintering of multicomponent Cu based metal powder. Mater Sci Technol 22 (2006) 1449-1455
12. Xie J.W., Fox P., O'Neill W., and Sutcliffe C.J. Effect of direct laser re-melting processing parameters and scanning strategies on the densification of tool steels. J Mater Process Technol 170 (2005) 516-523
13. Gu D.D., and Shen Y.F. WC-Co particulate reinforcing Cu matrix composites produced by direct laser sintering. Mater Lett 60 (2006) 3664-3668
14. p/Cu bulk MMCs prepared by direct laser sintering. J Alloys Compd 431 (2007) 112-120
15. Das S. Physical aspects of process control in selective laser sintering of metals. Adv Eng Mater 5 (2003) 701-711
16. Simchi A., and Pohl H. Direct laser sintering of iron-graphite powder mixture. Mater Sci Eng A 383 (2004) 191-200
17. Yang M.C., Xu J., and Hu Z.Q. Synthesis of WC-TiC35-Co10 nanocomposite powder by a novel method. Int J Refract Met Hard Mater 22 (2004) 1-7
18. Fischer P., Romano V., Weber H.P., Karapatis N.P., Boillat E., and Glardon R. Sintering of commercially pure titanium powder with a Nd: YAG laser source. Acta Mater 51 (2003) 1651-1662
19. Tolochko N., Mozzharov S., Laoui T., and Froyen L. Selective laser sintering of single- and two-component metal powders. Rapid Prototyping J 9 (2003) 68-78
20. Gu D.D., and Shen Y.F. Balling phenomena during direct laser sintering of multi-component Cu-based metal powder. J Alloys Compd 432 (2007) 163-166
21. Agarwala M., Bourell D., Beaman J., Marcus H., and Barlow J. Direct selective laser sintering of metals. Rapid Prototyping J 1 (1995) 26-36
22. Wilde G., and Perepezko J.H. Experimental study of particle incorporation during dendritic solidification. Mater Sci Eng A 283 (2000) 25-37
23. Yu J.Q., Yi W.Z., Chen B.D., and Chen H.J. Binary alloy phase diagrams. 1st ed. (1987), Shanghai Sientific & Technical Publishers, Shanghai
24. Wang J.X., Huang J.R., and Lin J.S. Solidification of metals and its control. 1st ed. (1983), China Machine Press, Beijing
25. Han Q., and Hunt J.D. Redistribution of particles during solidification. ISIJ Int 35 (1995) 693-699
26. 2 reinforced aluminium PMMCs. Compos Part A 36 (2005) 747-763
27. Zhang K., and Chen G.N. Effect of SiC particles on crystal growth of Al-Si alloy during laser rapid solidification. Mater Sci Eng A 292 (2000) 229-231
28. Simchi A., and Pohl H. Effects of laser sintering processing parameters on the microstructure and densification of iron powder. Mater Sci Eng A 359 (2003) 119-128
29. Gu D.D., and Shen Y.F. Microstructure of the WC-10%Co particulate reinforced Cu matrix composites fabricated by selective laser sintering. Rare Metal Mater Eng 35 (2006) 276-279
30. Gu D.D., and Shen Y.F. Processing and microstructure of submicron WC-Co particulate reinforced Cu matrix composites prepared by direct laser sintering. Mater Sci Eng A 435-436 (2006) 54-61