A closed-form solution to statically indeterminate adhesive joint problems-exemplified on ELS-specimens

International Journal of Adhesion and Adhesives

Volumn 28, Issue 7, 2008, Pages 350-361

  Alfredsson, K S ^a   Hogberg J L ^a  

^a UNIVERSITY OF SKÖVDE   (Sweden)

Author keywords

Beam adhesive layer model; C. Fracture mechanics; C. Joint design; C. Stress analysis

Indexed keywords

BOUNDARY CONDITIONS; CRACK PROPAGATION; FRACTURE ENERGY; STRESS ANALYSIS;

CLOSED-FORM SOLUTION; END LOADED SPLIT (ELS);

ADHESIVE JOINTS;

EID: 42949137074     PISSN: 01437496     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijadhadh.2007.10.002     Document Type: Article

References (23)

1. Volkersen O. Die Nietkraftverteilung in Zugbeanspruchten mit Konstanten Laschenquerschnitten. Luftfahrtsforschung 15 (1938) 41-47
2. Goland M., and Reissner E. The stresses in cemented joints. J Appl Mech 66 (1944) A17-A27
3. Hart-Smith LJ. Adhesive-bonded single-lap joints. NASA report, CR-112236, 1973.
4. Tsai M.Y., and Morton J. An evaluation of analytical and numerical solutions to the single-lap joint. Int J Solids Struct 31 18 (1994) 2537-2563
5. Oplinger D.W. Effects of adherend deflections in single lap joints. Int J Solids Struct 31 18 (1994) 2565-2587
6. Sun X., and Davidson B.D. Numerical evaluation of the effects of friction and geometric nonlinearities on the energy release rate in three- and four-point bend end-notched flexure tests. Eng Fract Mech 73 10 (2006) 1343-1361
7. Cornell R.W. Determination of stresses in cemented lap joints. J Appl Mech 20 3 (1953) 355-364
8. Bigwood D.A., and Crocombe A.D. Elastic analysis and engineering design formulae for bonded joints. Int J Adhes Adhes 9 (1989) 229-242
9. Alfredsson K.S. Constitutive behaviour and fracture of adhesive layers. Thesis for the degree of doctor of philosophy (2004), Chalmers University of Technology, Göteborg, Sweden
10. Högberg J.L. Mechanical behaviour of single-layer adhesive joints Thesis for the degree of licentiate of engineering (2004), Chalmers University of Technology, Göteborg, Sweden
11. Edlund U., and Klarbring A. Analysis of elastic and elastic-Plastic adhesive joints using a mathematical programming approach. Comput Methods Appl Mech Eng 78 (1990) 19-47
12. Klarbring A. Derivation of a model of adhesively bonded joints by the asymptotic expansion method. Int J Eng Sci 29 (1991) 493-512
13. Schmidt P. Analysis of adhesively bonded joints-an asymptotic approach. Linköping studies in science and technology, Thesis no. 925, Linköping University, Linköping, Sweden; 2001.
14. Wang C.H., Heller M., and Rose L.R.F. Substrate stress concentrations in bonded lap joints. J Strain Anal 33 5 (1998) 331-346
15. Salomonsson K., and Andersson T. Modeling and parameter calibration of an adhesive layer at the meso level. Mech Mater 40 1-2 (2007) 48-65
16. Högberg J.L., and Stigh U. Specimen proposals for mixed mode testing of adhesive layer. Eng Fract Mech 73 (2006) 2541-2556
17. Tsai M.Y., Oplinger D.W., and Morton J. Improved theoretical solutions for adhesive lap joints. Int J Solids Struct 35 12 (1998) 1163-1185
18. Davies G.D., et al. Comparison of test configurations for determination of mode II interlaminar fracture toughness results from international collaborative test programme. Plast Rubber Composites 28 9 (1999) 432-437
19. IIc, of structural adhesive joints: an effective crack length approach. Eng Fract Mech 72 (2005) 877-897
20. Eshelby J.D. The force on an elastic singularity. Philos Trans R Soc London A 244 (1951) 87-112
21. Rice J.R. A path independent integral and the approximate analysis of strain concentration by notches and cracks. J Appl Mech 35 (1968) 379-386
22. Alfredsson K.S. On the instantaneous energy release rate of the end-notch flexure adhesive joint specimen. Int J Solids Struct 41 (2004) 4787-4807
23. Alfredsson K.S., and Högberg J.L. Energy release rate and mode-mixity of adhesive joint specimens. Int J Fract 144 (2007) 267-283