Effects of high speed in the drilling of glass fibre reinforced plastic: Evaluation of the delamination factor

International Journal of Machine Tools and Manufacture

Volumn 48, Issue 6, 2008, Pages 715-720

  Campos Rubio, J ^a   Abrao, A M ^a   Faria, P E ^a   Correia, A Esteves ^b   Davim, J Paulo ^c  

^a FEDERAL UNIVERSITY OF MINAS GERAIS   (Brazil)

^b POLYTECHNIC INSTITUTE OF VISEU   (Portugal)

^c UNIVERSITY OF AVEIRO   (Portugal)

Author keywords

Delamination; Drilling; HSM; Polymer matrix composites

Indexed keywords

DELAMINATION; DRILLING; POLYMER MATRIX COMPOSITES;

DIGITAL ANALYSIS; HIGH SPEED MACHINING (HSM);

GLASS FIBER REINFORCED PLASTICS;

EID: 39749132229     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijmachtools.2007.10.015     Document Type: Article

References (13)

1. El-Sonbaty I., Khashaba U.A., and Machaly T. Factors affecting the machinability of GFR/epoxy composites. Composite Structures 63 (2004) 329-338
2. Velayudham A., Krishnamurthy R., and Soundarapandian T. Evaluation of drilling characteristics of high volume fraction fibre glass reinforced polymeric composite. International Journal of Machine Tools and Manufacture 45 (2005) 399-406
3. Callister W.D. Materials Science and Engineering: An Introduction. sixth ed. (2002), Wiley, Canada
4. Boyle M.A., Martin C.J., and Neuner J.D. Epoxy resin. In: Hansmann H. (Ed). Composites Compendium, ASM Handbook FB MVU (2003), Werkstofftechnologien, Kunststofftechnik
5. Davim J.P., Campos Rubio J.C., and Abrão A.M. A novel approach based on digital image analysis to evaluate the delamination factor after drilling composite laminates. Composites Science and Technology 67 (2007) 1939-1945
6. Davim J.P., Reis P., and Antonio C.C. Experimental study of drilling glass fibre reinforced plastics (GFRP) manufactured by hand lay-up. Composites Science and Technology 64 (2004) 289-297
7. Arul S., Vijayaraghavan L., Malhotrab S.K., and Krishnamurthy R. The effect of vibratory drilling on hole quality in polymeric composites. International Journal of Machine Tools and Manufacture 46 (2006) 252-259
8. Aoyama E., Nobe H., and Hirogaki T. Drilled hole damage of small diameter in printed wiring board. Journal of Materials Processing Technology 118 (2001) 436-441
9. Inoue H., Aoyama E., Hirogaki T., Ogawa K., Matushita H., Kitahara Y., and Katayama T. Influence of tool wear on internal damage in small diameter drilling in GFRP. Composite Structures 39 1-2 (1997) 55-62
10. 2-Cr coatings. Wear 258 (2005) 812-825
11. Davim J.P., Reis P., and Antonio C.C. Drilling fibre reinforced plastics (FRPs) manufactured by hand lay-up: influence of matrix (Viapal VUP 9731 and ATLAC 382-05). Journal of Materials Processing Technology 156 (2004) 1828-1833
12. Sardiñas R.Q., Reis P., and Davim J.P. Multi-objective optimization of cutting parameters for drilling laminate composite materials by using genetic algorithms. Composites Science and Technology 66 (2006) 3083-3088
13. Tsao C.C., and Hocheng H. Effects of special drill bits on drilling-induced delamination of composite materials. International Journal of Machine Tools and Manufacture 46 (2006) 1403-1416