The effect of the cutting fluid on surface roughness in boring of low carbon steel-technical communication

Machining Science and Technology

Volumn 11, Issue 4, 2007, Pages 553-560

  Yildiz, Y ^a   Gunay, M ^a   Seker, U ^a  

^a GAZI UNIVERSITY   (Turkey)

Author keywords

Boring; Chip formation; Cutting fluid; Surface roughness

Indexed keywords

CARBON STEEL; ENVIRONMENTAL IMPACT; HEALTH HAZARDS; SURFACE ROUGHNESS;

CHIP FORMATION; CUTTING SPEED; FEED RATE;

CUTTING FLUIDS;

EID: 37049033046     PISSN: 10910344     EISSN: 15322483     Source Type: Journal    
DOI: 10.1080/10910340701697052     Document Type: Article

References (29)

1. Adler, D.P.; Hü, W.S.; Michalek, D.J.; Sutherland, J.W. (2006) Examining the role of cutting fluids in machining and efforts to address associated environmental health concerns. Machining Science and Technology, 10: 23-58.
2. Andren, L.; Hakansson, L.; Brandt, A.; daemon, I. (2004) Identification of dynamic properties of boring bar vibrations in a continuous boring operation. Mechanical Systems and Signal, Processing, 18:869-001.
3. Avila, R.F.; Abrao, A.M. (2001) The effect of cutting fluids on the machining of hardened AISI 4340 steel. Journal of Materials Processing Technology, 119: 21-26.
4. Bailey, J.A. (1977a) Surface damage during machining of solution treated and aged 18% nickel maraging steel Part 1-unlubricated conditions. Wear, 42(2): 277-296.
5. Bailey, J.A. (1977b) Surface damage during machining of solution treated and aged 18% nickel maraging steel Part 2-lubricated conditions. Wear, 44(2): 297-303.
6. Beauchamp, Y.B.; Thomas, M.; Youssef, Y.A.; Masounave, J. (1996) Investigation of cutting parameter effects on. surface roughness in lathe boring operation by use of a full factorial design. Computers & Industrial Engineering, 31(3-4): 645-651.
7. Chou, Y.K.; Song, H. (2004) Tool nose radius effects on finish hard, turning. Journal of Materials Processing Technology, 148: 259-268.
8. Da Silva, M.B.; Wallbank, J. (1.999) Cutting temperature: Prediction and measurement methods-A review. Journal of Materials Processing Technology, 88: 195-202.
9. Davim, J.P. (2001) Anote on the determination of optimal cutting conditions for surface finish obtained in turning using design of experiments. Journal of Materials Processing Technology, 116: 305-308.
10. Diniz, A.E.; Micaroni, R. (2002) Cutting conditions for finish turning process aiming: The use of dry cutting. International Journal of Machine Tools & Manufacture, 42: 899-904.
11. El Baradie, MA (1996) Cutting fluids: Parti, characterisation. Journal of Materials Processing Technology, 56(1-4): 786-797.
12. Escolona, P.M.; Gassier, Z. (1.998) Influence of the critical cutting speed on the surface finish of turned steel. Wear, 218: 103-109.
13. Feng, C.X.; Wang, X. (2002) Development of empirical models for surface roughness prediction in finish turning. International Journal of Advanced, Manufacturing Technology, 20(5): 348-356.
14. Hung, N.P.; Yeo, S.H.; Oon, B.E. (1997) Effect of cutting fluid on the machinability of metal matrix composites. Journal of Materials Processing Technology, 67: 157-161.
15. Jawahir, I.S. (1988) The chip control factor in machinability assessments: Recent trends. Journal of Mechanical Working Technology, 17: 213-224.
16. Komanduri, R.; Hou, Z.B. (2001) Thermal modelling of the metal cutting process--Part III: Temperature rise distribution due to the combined effects of shear plane heat source and the Tool-chip interface frictional heat source. International Journal of Mechanical Sciences, 43: 89-107.
17. Kopac, J.; Bahor, M. (2001) Interaction of the workpiece material's technological past and machining parameters on. the desired quality of the product surface roughness. Journal of Materials Processing Technology, 109: 105-111.
18. Lin, W.S.; Lee, B.Y; Wu, C.L. (2001) Modeling the surface roughness and cutting force for turning. Journal of Materials Processing Technology, 108: 286-293.
19. Ng, E.G.; Aspinwall, D.K.; Brazil, D.; Monaghan, J. (1999) Modelling of temperature and forces when orthogonally machining hardened steel. International Journal of Machine Tools & Manufacture, 39: 885-903.
20. Rakie, R.; Rakic, Z. (2002) The influence of the metal working fluids on machine tool failures. Wear, 252: 438-444.
21. Sandvik Coromant Technical Editorial. Dept. (1996). Modem Metal Cutting-A Practical Handbook; Sandvik-Coromant Co. Inc., Sweden.
22. Shaw, M.C. (1986) Metal Cutting Principles; Oxford University Press, New York.
23. Stephenson, D.A.; Agapiou, J.S. (2006) Metal Cutting 'Theory and Practice; 2nd edition, Taylor & Francis, CRC Press, Boca Raton, pp. 551-559.
24. Seah, K.H.W.; Li, X.; Lee, K.S. (1995) The effect of applying coolant on tool wear in metal machining. Journal of Materials Processing Technology, 48(1-4): 495-501.
25. Sheng P.S.; Oberwalleney S. (1997) Life-Cycle planning of cutting fluids-A review. ASME Journal of Manufacturing Science and Engineering, 119(11): 791-800.
26. Sokovic, M.; Mijanovic, K. (2001) Ecological aspects of the cutting fluids and its influence on quantifiable parameters of the cutting processes. Journal of Materials Processing Technology, 109:181-189.
27. Tay, F.E.H.; Sikdar, S.K.; Mannan, M.A. (2002) Topography of the flank wear surface. Journal of Materials Processing Technology, 120: 243-248.
28. Thomas, M.; Beauchamp Y.; Youssef, A.Y.; Masounave, J. (1996) Effect of tool vibrations on surface roughness during lathe dry turning process. Computers & Industrial Engineering, 31(3-4): 637-644.
29. Zou, O.; Barber, G.G.; Yang, L. (2005) Optimization of hollow cantilevered boring bar stiffness. Machining Science and Technology, 9: 325-343.