메뉴 건너뛰기




Volumn 4, Issue , 2007, Pages 1973-1977

Microstructural characteristics of micro-injection molded thermoplastics

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; INJECTION MOLDING; MICROSTRUCTURE; NANOINDENTATION; POLYETHYLENES; SHRINKAGE;

EID: 34648820496     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper
Times cited : (5)

References (9)
  • 1
    • 33646677030 scopus 로고    scopus 로고
    • Fundamental study on structure development of thin-wall injection molded products
    • Ito, H., et al., Fundamental study on structure development of thin-wall injection molded products. Theoretical and Applied Mechanics Japan, 2005. 54: p. 263-268.
    • (2005) Theoretical and Applied Mechanics Japan , vol.54 , pp. 263-268
    • Ito, H.1
  • 2
    • 1542500487 scopus 로고    scopus 로고
    • Effects of Process Parameters on the Micro Molding Process
    • Zhao, J., et al., Effects of Process Parameters on the Micro Molding Process. Polymer Engineering and Science, 2003. 43(9): p. 1542.
    • (2003) Polymer Engineering and Science , vol.43 , Issue.9 , pp. 1542
    • Zhao, J.1
  • 3
    • 3042742259 scopus 로고    scopus 로고
    • Micromoulding: Process measurements, product morphology and properties
    • Whiteside, B.R., et al., Micromoulding: Process measurements, product morphology and properties. Plastics, Rubber and Composites, 2004. 33(1): p. 11.
    • (2004) Plastics, Rubber and Composites , vol.33 , Issue.1 , pp. 11
    • Whiteside, B.R.1
  • 5
    • 0036735589 scopus 로고    scopus 로고
    • Simulation of the filling process in micro channels for polymeric materials
    • Yao, D. and B. Kim, Simulation of the filling process in micro channels for polymeric materials. Journal of Micromechanics and Microengineering, 2002.
    • (2002) Journal of Micromechanics and Microengineering
    • Yao, D.1    Kim, B.2
  • 6
    • 0036750732 scopus 로고    scopus 로고
    • Performance and simulation of thermoplastic micro injection molding
    • Piotter, V., et al., Performance and simulation of thermoplastic micro injection molding. Microsystem Technologies, 2002. 8(6): p. 387.
    • (2002) Microsystem Technologies , vol.8 , Issue.6 , pp. 387
    • Piotter, V.1
  • 7
    • 0018006057 scopus 로고    scopus 로고
    • Tan, V. and M.R. Kamal, Morphological Zones and Orientation in Injection-Molded Polyethylene. 1978. 22(8): p. 2341.
    • Tan, V. and M.R. Kamal, Morphological Zones and Orientation in Injection-Molded Polyethylene. 1978. 22(8): p. 2341.
  • 8
    • 0020203421 scopus 로고    scopus 로고
    • Katti, S.S. and J.M. Schultz, MICROSTRUCTURE OF INJECTION-MOLDED SEMICRYSTALLINE POLYMERS - A REVIEW. Polymer Engineering and Science, 1982. 22(16): p. 1001-1017.
    • Katti, S.S. and J.M. Schultz, MICROSTRUCTURE OF INJECTION-MOLDED SEMICRYSTALLINE POLYMERS - A REVIEW. Polymer Engineering and Science, 1982. 22(16): p. 1001-1017.


* 이 정보는 Elsevier사의 SCOPUS DB에서 KISTI가 분석하여 추출한 것입니다.