Deterministic modeling of honed cylinder liner friction

Tribology Transactions

Volumn 50, Issue 2, 2007, Pages 248-256

  Bolander, Nathan W ^a   Sadeghi, Farshid ^a  

^a PURDUE UNIVERSITY   (United States)

Author keywords

Friction; Mixed Lubrication; Piston Rings; Surface Roughness Effects

Indexed keywords

LUBRICATION; NUMERICAL METHODS; PISTON RINGS; SURFACE ROUGHNESS;

CYLINDER LINER; MIXED LUBRICATION; NUMERICAL EQUIVALENT;

FRICTION;

FRICTION; LUBRICATION; NUMERICAL METHODS; PISTON RINGS; SURFACE ROUGHNESS;

EID: 34548708550     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/10402000701309471     Document Type: Article

References (21)

1. Jeng, Y. (1992), "Theoretical Analysis of Piston-Ring Lubrication Part 1-Fully Flooded Lubrication," Trib. Trans., 35, pp 696-706.
2. Greenwood, J. A. and Tripp, X H. (1971), "The Contact of Two Nominally Flat Rough Surfaces," Proc Inst. Mech. Eng., 185, pp 625-633.
3. Rohde, S. M., Whitaker, K. W. and McAllister, G. T. (1980), "A Mixed Friction Model for Dynamically Loaded Contacts with Application to Piston Ring Lubrication," Surface Roughness Effects in Hydrodynamic and Mixed Lubrication, ASME Winter Annual Meeting, pp 19-50.
4. Hu, Y., Cheng, H. S., Arai, T., Kobayashi, Y and Aoyama, S. (1994), "Numerical Simulation of Piston Ring in Mixed Lubrication - A Non-Axisymmetrical Analysis," ASME J. Tribol., 116, pp 470-478.
5. Bolander, N. W., Steenwyk, B. D., Sadeghi, F. and Gerber, G. R. (2005), "Lubrication Regime Transitions at the Piston Ring-Cylinder Liner Interface," Proc. Inst. Mech. Eng. J J. Eng. Tribol., 219, pp 19-31.
6. Bolander, N. W., Steenwyk, B. D., Kumar, A. and Sadeghi, F. (2004), "Film Thickness and Friction Measurement of Piston Ring Cylinder Liner Contact with Corresponding Modeling including Mixed Lubrication," ASME-ICED Fall Technical Conference Proceedings, ASME Paper ICEF2004-903.
7. Jocsak, J., Tomanik, E., Wong, V. and Tian, T. (2005), "The Characterization and Simulation of Cylinder Liner Surface Finishes," ASME-ICED Spring Technical Conference Proceedings, ASME Paper ICES2005-1080.
8. Jiang, X., Hua, D. Y., Cheng, H. S., Ai, X. and Lee, S. C. (1999), "A Mixed Elastohydrodynamic Lubrication Model with Asperity Contact," ASME J. Tribol., 121, pp 481-491.
9. Hu, Y., Zhu, D. (2000), "A Full Numerical Solution to the Mixed Lubrication in Point Contacts," ASME J. Tribol., 122, pp 1-9.
10. Zhao, J., Sadeghi, F. and Hoeprich, M. H. (2001), "Analysis of EHL Circular Contact Start Up: Part I - Mixed Contact Model with Pressure and Film Thickness Results," ASME J. Tribol., 123, pp 67-74.
11. Hill, S., Kantola, T., Brown, J. and Hamelink, J. (1995), "An Experimental Study of the Effect of Cylinder Bore Finish on Engine Oil Consumption," SAE paper 950938.
12. Hill, S. (2001), "Cylinder Bore Finishes and Their Effect on Oil Consumption," SAE paper 2001-01-3550.
13. Srivastava, D. and Agarwal, A. (2004), "Experimental Investigations on the Effect of Liner Surface Properties on Wear in Non-Firing Engine Simulator," SAE paper 2004-01-0605.
14. Michail, S. and Barber, G. (1995), "The Effects of Roughness on Piston Ring Lubrication - Part I: Model Development," Trib. Trans., 38, pp 19-26.
15. Michail, S. and Barber, G. (1995), "The Effects of Roughness on Piston Ring Lubrication - Part II: The Relationship between Cylinder Wall Surface Topography and Oil Film Thickness," Trib. Trans., 38, pp 173-177.
16. Jocsak, J., Li, Y., Wong, V. and Tian, T (2005), "Analyzing the Effects of Three-Dimensional Cylinder Linder Surface Texture on Ring-Pack Performance with a Focus on Honing Groove Cross-Hatch Angle," ASME-ICED Fall Technical Conference Proceedings, ASME Paper ICEF2005-1333.
17. Lu, S., Iyer, K. and Hu, S.J. (2004), "Functional Charactierization of Surface Roughness Generated by PlateauHoning Process Using Wavelet Analysis," SAE paper 2004-01-1558.
18. Stanley, H.M. and Kato, T. (1997) "An FFT-Based Method for Rough Surface Contact," ASME J. Tribol., 119, pp 481-485.
19. Kumar, A., Sadeghi, F. and Krousgrill, C.M. (2006), "Effects of Surface Roughness on Normal Contact Compression Response," Proc. Inst. Mech. Eng. J J. Eng. Tribol., 220, pp 65-77.
20. Hill, I. D., Hill, R. and Holder, R. L. (1976) "Fitting Johnson Curves by Moments," Applied Statistics, 25, pp 180-189.
21. Bakolas, V. (2003), "Numerical Generation of Arbitrarily Oriented Non-Gaussian Three-Dimensional Rough Surfaces," Wear, 254, pp 546-554.